Touch up paint; Scratches; Chips; See photos for condition
Sheet Metal (fiberglass) Condition
Scrapes; See photos for condition
General Appearance #1
Control Station
Seats/Armrests
Seat Belts
Not equipped
Horn
Operational
Safety Lock Out/Stop
Hydraulic Controls
Drivetrain Controls
Oil Pressure
The fault indicator shuts off after the engine oil pressure rises.
Engine Warning Lights
Operational
Travel Alarm
Inoperable
Hour Meter/Odometer
1,506 Hours; Operational hour meter
- IronPlanet makes no guarantees as to actual hours/miles; we can only report what can be visually observed.
Limited Function Check
The main components operated except as noted.
Hour Meter/Odometer
Engine
Make and Model
Komatsu 2D70E-5 SBA engine
Fuel Type
Diesel
Emission Control Label
US EPA certification label
Blow by @ idle (subjective observation)
Minimal
Starter
Operational
Injector Pump
Operational
Exhaust System
No visible damage
Radiator
Oil Leaks
None seen
Fuel Leaks
None seen
Cooling System Leaks
None seen
Limited Function Check
The engine started and ran.
Emission Control Label
Drivetrain
Operational test is limited to low speed in a confined flat area without load. Full transmission shifting and functionality of all drive systems cannot be fully verified. Inspector listens for abnormal noises, observes leaks and notes physical damage.
Drive Motors
Final Drives
Limited Function Check
The drivetrain was operational except as noted.
Drivetrain #1
Hydraulics
Pumps (Hydraulics)
Valves
Hydraulic Tank
Low oil level
Hoses (Hydraulics)
Auxiliary Hydraulic Plumbing
Not operationally checked
Boom Swing Cylinders
Minimal pin and bushing movement
Boom Lift Cylinders
Minimal pin and bushing movement
Stick Cylinder
Minor to moderate pin and bushing movement
Bucket Cylinder
Minor to moderate pin and bushing movement
Limited Function Check
The hydraulic system was operational except as noted.
Hydraulics #1
Chassis
IronPlanet pin connection pivot point wear inspections are limited to sound, sight and feel observations. Dial indicator testing is not performed.
Boom Condition
Minor dents on bottom of boom
Stick Condition
Minor dents on inside of stick
Boom Base Pin and Bushings
Minimal movement
Pin and Bushings Boom to Stick
Minor to moderate movement
Pin and Bushings Stick to Bucket
Heavy movement
Stick Length
2' Stick
Turn-table Bearing
Bottom Covers
Limited Function Check
The main components were operational with movement as indicated.
Chassis #1
Undercarriage
Undercarriage components photos (links, bushings, sprockets, idlers, rollers, grousers) are selected as representative. Bidders are encouraged to review photos using the zoom feature to judge condition in detail.
Overall Machine Width (Outsides of tracks.)
33"
Grouser Height Measurement
Left side: 15 mm; Right side: 15 mm
Track Belt Width
7" Track belts
Track Belt Condition
See photos for condition; Cuts; Damaged drive lugs
Rubber Belt Drive Lugs
See photos for condition
Carrier Rollers
See photos for condition
Front Idler Wear
See photos for condition
Rear idler wear
See photos for condition
Track Rollers
See photos for condition
Sprockets
See photos for condition
Undercarriage #1
Specialty
Excavator Bucket Condition
12" Bucket; Worn; Dented
Backhoe / Excavator Bucket Shanks and Teeth
Worn or damaged edge
Blade Condition
33 1/2" Blade
Blade Cutting Edge Condition
Specialty #1
Oil Sample Analysis
Oil sample analysis not available.
Disputes:
This item is offered with IronClad Assurance® protection. With IronClad Assurance®, if a buyer discovers that the item is not substantially in the condition as represented in this inspection report, the buyer may submit a written dispute claim to IronPlanet. Following submission of a written dispute claim, IronPlanet will investigate the claim, re-inspecting the equipment item as necessary, and determine a fair and mutually beneficial resolution. Please note that IronPlanet inspections are performed solely for the purpose of reporting the visible condition of the equipment's major systems and attachments on the day of the inspection and do not include load testing or digging/lifting. These inspections are not designed nor intended to detect latent defects, or conditions that could only be found in connection with the physical dismantling of the equipment or the use of diagnostic tools or techniques. This inspection report includes ratings, comments, and photos of the various components of the item. Knowledgeable buyers are expected to carefully review all of the available information in the inspection report, including all photographs, in order to make the best bidding and buying decision possible. Please contact IronPlanet Customer Care at 888-433-5426 to file a dispute, and please review the Terms & Conditions, to which all approved bidders have agreed.
Buyer is responsible for all costs related to transporting the item.
Item must be picked up within 8 business days of the auction, or the buyer will incur storage charges.
The location information will be provided once full payment has been received.
The buyer will have the option during Checkout to automatically receive competing quotes.
Pickup Terms Failure to follow these terms may result in the seller turning away the attempt to pick up the purchased item.
Hours: 8:00 am - 4:30 pm; Mon-Fri
Call 24 hrs in advance
Loading Dock NOT Available
Ramps NOT Available
Forklift Available
Driver MUST bring a copy of the IronPlanet Transportation Release to pick the item up.
Within 3 business days after the auction, the buyer must submit full payment, including applicable taxes and fees.
For this item, payment is due on or before February 27.
This item is subject to Pennsylvania sales tax unless proof of exemption or declaration of common carrier shipment to another state is presented during item checkout. (Read more)
Buyer must pay a transaction fee (see Buyer fees).
Payment can be made by wire transfer (recommended), certified bank check (U.S. customers only), or credit card (when full payment amount is $5,000 or less).
All bids are binding and cannot be retracted. Failure to make full payment will result in a Default Fee Penalty.
If you are looking to finance your purchase, we recommend you get
pre-approved in advance of the auction. Here are three companies we recommend
who specialize in equipment financing:
GE Capital
Thank you for your interest in applying for a GE Capital loan. GE Capital
provides equipment leasing, financing and other services to deliver significant
benefits for your business. Our products and services are customized with
flexible structure and payment terms to match your unique needs and goals. In
order to start the process of applying for a loan, please complete the attached
credit
application and forward to Bryan
Grittner or fax the application to (469) 519-4394.
Cat Financial - Capital Solutions
Get a Pre-Approved Line of Credit Be prepared for
upcoming auctions by arranging a line of credit from Cat Financial. Time is
money during an auction, and seconds count. Let Cat Financial provide you with
the pre-arranged purchasing power that lets you focus on the equipment you need.
Apply today.
Pinnacle Capital
Full Spectrum Financing for IronPlanet® Auctions
IronPlanet has been offering financing for your purchases through a
partnership with Pinnacle Capital since 2002. Pinnacle knows what it takes to
get auction deals done fast and has facilitated several millions of dollars in
online purchases. Get a pre-approved line of credit set-up before you place a
bid to confirm your buying power. Click here to learn more about Pinnacle's financing products.
To qualify, complete Pinnacle's online
application. Once approved, they'll take care of the rest. Please contact
Matt Perini at 800-566-1993 or by
email to discuss the transaction further.
Powertrain Coverage. Covers major drive train components- engine, torque hubs, transmission & front
and rear axles - and more
Available in North America. May be purchased by residents of U.S. and Mexico only, for equipment operated
within U.S., Mexico or Canada.
OEM parts and service. All repairs are made by an OEM authorized repair facility with genuine OEM replacement
parts installed by OEM trained technicians.
