There is significant rust and corrosion on the sheet metal. The grill bars are missing. There are holes on the fiberglass hood. The insulation retainers inside the hood are falling out. The utility box has some cracks and holes in the fiberglass and the doors are difficult to close. The front hood mounts are badly rusted.
General Appearance #1
Control Station
Steps/Ladders
Hand Rails
Mirrors
Glass
Seats/Armrests
Torn cover
Seat Belts
Buried in seat,
Horn
Functional; The horn is weak.
Steering Controls
Stiff; Steers Hard;
Drivetrain Controls
Oil Pressure
Approximately 33 PSI; at idle
Exterior Lights Operational
Yes
Engine Warning Lights
Inoperable
Gauges
Functional
Hour Meter/Odometer
Functional; 131,160 Miles; The odometer counts hours while the crane operates; Functional hours: 8,017
- IronPlanet makes no guarantees as to actual hours/miles; we can only report what can be visually observed.
Heater
Functional
Limited Function Check
The components that were checked functioned except as noted.
Hour Meter/Odometer
Control Station - Ground
Hydraulic Controls
Stiff
Exterior Lights Operational
Yes
Engine Warning Lights
Functional
Horn
Functional
Limited Function Check
The components that were checked functioned except as noted.
Control Station - Ground #1
Engine
Make and Model
Ford 6 Cylinder engine
Fuel Type
Diesel
Engine Brake
No
Emission Control Label
US EPA certification label
Block Heater
Yes
Blow by @ idle (subjective observation)
Visible
Starter
Turbo or Blower
Operational
Injector Pump
Seepage residue
Exhaust System
Rust Penetration
Radiator
Head Gasket Leaks
Residue from unknown source
Oil Leaks
There is seepage residue on the oil pan, the rear and side of the engine.
Fuel Leaks
None seen
Cooling System Leaks
None seen
Limited Function Check
The engine started and ran during a limited check. Required ether to start. The cold start ether canister is secured with electrical tape. See oil report.
Blow by @ idle (subjective observation)
Drivetrain
Operational test is limited to low speed in a confined flat area without load. Full transmission shifting and functionality of all drive systems cannot be fully verified. Inspector listens for abnormal noises, observes leaks and notes physical damage.
Transmission
Functions but could not verify shifting in all ranges; There is oil residue on the rear of the transmission pan. The shift lever is lose and the shifter unlock mechanism is loose.
Torque Converter
Could not functionally verify in all ranges.
Center Drive Axle
There is caked dirt and oil residue on the front of the housing.
Rear Drive Axle
Limited Function Check
The drivetrain functioned during a limited check without a load. The PTO splitter box is leaking from the input shaft.
Drivetrain #1
Hydraulics
Pumps (Hydraulics)
Wet with residue; Caked with dirt and residue.
Valves
Hydraulic Tank
Hoses (Hydraulics)
Worn; Weathered; Cracked; Some fittings have rust and/or corrosion.
Auxiliary Hydraulic Plumbing
Yes; Not operationally checked; There is a hydraulic hose on the reel, the reel is rusted.
Cylinder(s)
Seepage residue; The second stage boom cylinder has seepage.
Cylinder Pins and Bushings
Wear consistent with age.
Limited Function Check
The hydraulic system was operational during a limited check without a load. See oil report.
Hydraulics #1
Chassis
IronPlanet pin connection pivot point wear inspections are limited to sound, sight and feel observations. Dial indicator testing is not performed.
Steering Linkage
Oil residue on the steering box.
Steering Wheel Play
Minor; Steers hard;
Brake Type
Air
Master Cylinder/Brake Control
Brake Lines/Hoses
Park Brake
Held against power
Limited Function Check
The brake system functioned, stopping and holding the machine.
Springs/Hangers Condition
Bed/Bed Box
The truck is 182" long and 96" wide. The inside bed dimensions are 158" x 59".
External Electrical / Air Connections
In place, not tested
Frame Condition
Rusty
Tire Size
Front 315/80R 22.5; Rear 11 R 22.5; Brand(s): Continental, Kumho
Performs within tolerance expected for age and hours
Chassis #1
Chassis Boom
IronPlanet turn-table bearing and pin connection pivot point wear inspections are limited to sound, sight and feel observations. Dial indicator testing is not performed.
Boom Condition (Telescopic)
Boom Wear Guides
Main Boom Length
26' Extended; 175" fully retracted
Max Weight Capacity
19,510 lbs
Stabilizer Beams
Oily
Stabilizer Cylinders
Hook Block
Swivel hook
Attachment
Winch; Operable; Pintle hitch
Chassis Boom #1
Oil Sample Analysis
Engine
Hydraulic
date of analysis
Dec 02, 2009
Dec 02, 2009
Silicon
6 PPM
10 PPM
Lead
2 PPM
0 PPM
Tin
0 PPM
0 PPM
Copper
2 PPM
4 PPM
Aluminum
2 PPM
0 PPM
Silver
0 PPM
0 PPM
Nickel
0.3 PPM
0.1 PPM
Chromium
1.1 PPM
0.4 PPM
Iron
33 PPM
8 PPM
Glycol
NEG
N/A
Water
NEG
NEG
Fuel
<5%
N/A
Disputes:
This item is offered with IronClad Assurance® protection. With IronClad Assurance®, if a buyer discovers that the item is not substantially in the condition as represented in this inspection report, the buyer may submit a written dispute claim to IronPlanet. Following submission of a written dispute claim, IronPlanet will investigate the claim, re-inspecting the equipment item as necessary, and determine a fair and mutually beneficial resolution. Please note that IronPlanet inspections are performed solely for the purpose of reporting the visible condition of the equipment's major systems and attachments on the day of the inspection and do not include load testing or digging/lifting. These inspections are not designed nor intended to detect latent defects, or conditions that could only be found in connection with the physical dismantling of the equipment or the use of diagnostic tools or techniques. This inspection report includes ratings, comments, and photos of the various components of the item. Knowledgeable buyers are expected to carefully review all of the available information in the inspection report, including all photographs, in order to make the best bidding and buying decision possible. Please contact IronPlanet Customer Care at 888-433-5426 to file a dispute, and please review the Terms & Conditions, to which all approved bidders have agreed.
Buyer is responsible for all costs related to transporting the item.
Item must be picked up within 8 business days of the auction.
The exact item location will be provided once full payment has been received.
The buyer will have the option during Checkout to automatically receive competing quotes.
Pickup Terms Failure to follow these terms may result in the seller turning away the attempt to pick up the purchased item.
Hours: 8 - 4 Mon - Fri
You must call at least 24 hours in advance to schedule pickup
No Loading Dock, Ramps, or Forklift Available: Only RGN or trailers with ramps can be used to pick up this item at this location. Seller will not allow item to be loaded on a step-deck or flatbed trailer without the appropriate ramps.
Driver MUST bring a copy of the IronPlanet Transportation Release to pick the item up.
Unit must be picked up within 30 days of sale or incur a $100.00 per day storage fee – abandonment proceedings will start at 31 days
Within 3 business days after the auction, the buyer must submit full payment, including applicable taxes and fees.
For this item, payment is due on or before January 20.
This item is subject to 7% Minnesota sales tax unless proof of exemption or declaration of Common Carrier shipment to another state is presented during item Checkout. (Read more)
Buyer must pay a transaction fee (see Buyer fees).
Payment can be made by wire transfer (recommended), certified bank check (U.S. customers only), or credit card (when full payment amount is $5,000 or less).
All bids are binding and cannot be retracted. Failure to make full payment will result in a Default Fee Penalty.
If you are looking to finance your purchase, we recommend you get
pre-approved in advance of the auction. Here are three companies we recommend
who specialize in equipment financing:
GE Capital
Thank you for your interest in applying for a GE Capital loan. GE Capital
provides equipment leasing, financing and other services to deliver significant
benefits for your business. Our products and services are customized with
flexible structure and payment terms to match your unique needs and goals. In
order to start the process of applying for a loan, please complete the attached
credit
application and forward to Bryan
Grittner or fax the application to (469) 519-4394.
Cat Financial - Capital Solutions
Get a Pre-Approved Line of Credit Be prepared for
upcoming auctions by arranging a line of credit from Cat Financial. Time is
money during an auction, and seconds count. Let Cat Financial provide you with
the pre-arranged purchasing power that lets you focus on the equipment you need.
Apply today.
Pinnacle Capital
Full Spectrum Financing for IronPlanet Auctions
IronPlanet has been offering financing for your purchases through a
partnership with Pinnacle Capital since 2002. Pinnacle knows what it takes to
get auction deals done fast and has facilitated several millions of dollars in
online purchases. Get a pre-approved line of credit set-up before you place a
bid to confirm your buying power. Click here to learn more about Pinnacle's financing products.
To qualify, complete Pinnacle's online
application. Once approved, they'll take care of the rest. Please contact
Matt Perini at 800-566-1993 or by
email to discuss the transaction further.
Powertrain Coverage. Covers major drive train components- engine, torque hubs, transmission & front
and rear axles - and more
Available in North America. May be purchased by residents of U.S. and Mexico only, for equipment operated
within U.S., Mexico or Canada.
OEM parts and service. All repairs are made by an OEM authorized repair facility with genuine OEM replacement
parts installed by OEM trained technicians.
888-433-5426
