Minor dents/ scrapes; Surface rust in paint loss areas. Latch missing on rear panel.
Serial Number / VIN
Control Station
Steps/Ladders
Hand Rails
Mirrors
Missing
Seats/Armrests
Torn cover
Seat Belts
Dirty
Horn
Functional
Hydraulic Controls
Steering Controls
Powertrain Controls
Oil Pressure
The fault indicator shuts off after the engine oil pressure rises.
Exterior Lights Functional
Yes
Engine Warning Lights
Functional
Travel Alarm
Functional
Gauges
Functional
Hour Meter/Odometer
Functional; 4,619 Hours
- IronPlanet makes no guarantees as to actual hours/miles; we can only report what can be visually observed.
Heater
Functional
Limited Function Check (cs)
The components that were checked functioned except as noted.
Hour Meter/Odometer
Engine
Engine Make and Model
Engine make: Cat; 3116 engine; Serial #: 4TF67678
Fuel Type
Diesel
Emission Control Label
US EPA certification label
Blow by @ idle (subjective observation)
Visible
Starter
Turbo or Blower
Operational
Injector Pump
Operational
Exhaust System
The stack is bent and damaged. The tip is rusted.
Radiator
Minor plugging of fins
Head Gasket Leaks
None seen
Oil Leaks
None seen
Fuel Leaks
None seen
Cooling System Leaks
None seen
Limited Function Check
After jump starting the engine ran with smoke that mostly cleared. See oil report.
Emission Control Label
Drivetrain
Operational test is limited to low speed in a confined flat area without load. Differential interlocks, full transmission shifting and functionality of all drive axles cannot be fully verified. Inspector listens for abnormal noises, observes leaks and notes physical damage.
Service Brakes
Final Drives
Limited Function Check (Drivetrain-Track)
The drivetrain was operational during a limited check without a load. See oil report.
Drivetrain #1
Hydraulics
Pumps (Hydraulics)
Not visible
Valves
Hydraulic Tank
Hoses (Hydraulics)
Weathered
Cylinders
Cylinder Pins and Bushings
Wear consistent with hours and age
Limited Function Check
The hydraulic system was operational during a limited check without a load.
Hydraulics #1
Chassis
IronPlanet turn-table bearing and pin connection pivot point wear inspections are limited to sound, sight and feel observations. Dial indicator testing is not performed.
Roller Frames
Belly pans
Oil residue
Equalizer Bar Pivot Wear
Normal wear
Limited Function Check (loader)
The main components were operational with wear.
Push arm/C-frame condition
Push Arm Trunnions
Wear consistent with hours and age
Tilt/angle Linkage Pins and Bushings
Wear consistent with hours and age
Blade Trunnions/bushings
The blade hangs low on the left side.
Blade Lift Linkage Pins and Bushings
Wear consistent with hours and age
Limited Function Check (dozer)
The main dozer components functioned with wear.
Chassis #1
Undercarriage
Undercarriage components photos (links, bushings, sprockets, idlers, rollers, grousers) are selected as representative. Bidders are encouraged to review photos using the zoom feature to judge condition in detail.
Overall width (outside to outside of shoes)
119" Overall width
Track Tensioners
See photos
Shoe Width
34" shoe width
Grouser height
29-30mm
Track link wear
See photos; Worn
Pins and Bushings Turned?
No
Pins and bushing wear
See photos; Worn
Carrier rollers wear
See photos
Track rollers wear
See photos
Front idler wear
See photos
Rear idler wear
See photos
Sprockets
See photos
Undercarriage #1
Specialty
Blade Condition
154" Blade width; The blade is dented along the side and top edges.
Blade Cutting Edge Condition
Reversible-Not turned
Other
Drawbar
Specialty #2
Oil Sample Analysis
Engine
Transmission
date of analysis
Oct 27, 2009
Oct 27, 2009
Silicon
2 PPM
7 PPM
Lead
0 PPM
4 PPM
Tin
1 PPM
2 PPM
Copper
0 PPM
47 PPM
Aluminum
1 PPM
2 PPM
Silver
0.1 PPM
0.3 PPM
Nickel
0.2 PPM
0.1 PPM
Chromium
0.3 PPM
0.2 PPM
Iron
4 PPM
36 PPM
Glycol
NEG
N/A
Water
NEG
NEG
Fuel
<5%
N/A
Note: This condition inspection report is the result of an impartial, systematic, documented process focused on the establishment of the general, overall mechanical condition of a piece of equipment, or of a vehicle, at a specific time. The purpose of the inspection is to establish the "as-is" operational capability of the machine. It is not a performance or load test on the equipment.
Pickup Terms Failure to follow these terms may result in the seller turning away the attempt of your driver to pick up the purchased item.
Buyer will be responsible for any transportation charges issued by the driver.
888-433-5426
