Minor dents, scrapes and surface rust in the paint loss areas.
Serial Number / VIN
Control Station
Hydraulic Controls
Steps/Ladders
Hand Rails
Mirrors
Glass
Seats/Armrests
Seat Belts
Horn
Functional
Powertrain Controls
Steering Controls
Oil Pressure
The fault indicator shuts off after the engine oil pressure rises.
Exterior Lights Functional
Yes
Engine Warning Lights
Functional
Travel Alarm
Functional
Gauges
Functional
Hour Meter/Odometer
4586.; Functional; Hours
- IronPlanet makes no guarantees as to actual hours/miles; we can only report what can be visually observed.
Indication of Additional Hours
There is an hour meter replacement/change label that has the following reading on it: 421 is the legible number on the label. The label is damaged and not complete.
Air Conditioner
Ambient temperature too cold to check
Heater
Functional
Disconnect Control
Limited Function Check (cs)
The components that were checked functioned except as noted.
Hour Meter/Odometer
Engine
Engine Make and Model
Engine make: Cat; 3054T engine; Serial #: ?
Fuel Type
Diesel
Emission Control Label
Torn or unreadable
Block Heater
Yes
Blow by @ idle (subjective observation)
Minimal
Starter
Turbo or Blower
Operational
Injector Pump
Operational
Exhaust System
Radiator
Head Gasket Leaks
Residue from unknown source
Oil Leaks
None seen
Fuel Leaks
None seen
Cooling System Leaks
None seen
Limited Function Check
The engine started and ran during a limited check. See oil report.
Blow by @ idle (subjective observation)
Drivetrain
Operational test is limited to low speed in a confined flat area without load. Differential interlocks, full transmission shifting and functionality of all drive axles cannot be fully verified. Inspector listens for abnormal noises, observes leaks and notes physical damage.
Transmission
Torque Converter
Possible noise
Differential (front)
Differential (rear)
Final Drives
Limited Function Check
The drivetrain functioned during a limited check without a load.
The hydraulic system was operational during a limited check without a load. See oil report.
Hydraulics #1
Chassis
IronPlanet turn-table bearing and pin connection pivot point wear inspections are limited to sound, sight and feel observations. Dial indicator testing is not performed.
Steering Linkage
Brake Type
Hydraulic
Master Cylinder/Brake Control
Brake Lines/Hoses
Park Brake
Unable to test w/slope
Limited Function Check (Brakes)
The brake system functioned, stopping and holding the machine.
Frame Condition
Tire Size (4)
12.5/80-18 front tires; 21L-24 rear tires
Tire Condition
Cuts
Tread Depth (4 tires)
RF 8 mm; LF 10 mm; RR 17 mm; LR 17 mm
Wheel Condition
Wheel Studs, Nuts, Lugs
Lift Arm Condition
Chassis to Arm Pins
Tilt Linkage Pins and Bushings
Loose
Quick Coupler to Arms Pins
Wear consistent with hours and age
Limited Function Check (rt machines)
The main chassis components functioned during a limited check.
Boom Condition
Scratched; Deformed
Stick Condition
Dented; Scratched
Stick Type
Extendable stick
Extendahoe Stick Guide
Boom Lock (Backhoe)
Boom Base Pin and Bushings
Heavy wear
Pin and Bushings Boom to Stick
Wear consistent with hours and age
Pin and Bushings Stick to Bucket
Coupler to bucket is loose.
Outriggers
Street pads
Stabilizer Cylinders
Limited Function Check (Backhoe)
The main components were functional with minor to visible pivot point wear.
Chassis #1
Specialty
Backhoe / Excavator Bucket Condition
24" Rear bucket
Quick Coupler
Manual coupler; Wear at pin connections
Loader Bucket Cutting Edge
Reversible-turned
Loader Bucket Condition
94" loader bucket; Cracked
Specialty #1
Oil Sample Analysis
Engine
Hydraulic
date of analysis
Oct 16, 2009
Oct 16, 2009
Silicon
17 PPM
2 PPM
Lead
3 PPM
0 PPM
Tin
5 PPM
0 PPM
Copper
8 PPM
5 PPM
Aluminum
4 PPM
0 PPM
Silver
0.1 PPM
0 PPM
Nickel
3.3 PPM
0.1 PPM
Chromium
1.3 PPM
0.5 PPM
Iron
82 PPM
3 PPM
Glycol
NEG
N/A
Water
NEG
NEG
Fuel
<5%
N/A
Note: This condition inspection report is the result of an impartial, systematic, documented process focused on the establishment of the general, overall mechanical condition of a piece of equipment, or of a vehicle, at a specific time. The purpose of the inspection is to establish the "as-is" operational capability of the machine. It is not a performance or load test on the equipment.
Pickup Terms Failure to follow these terms may result in the seller turning away the attempt of your driver to pick up the purchased item.
Buyer will be responsible for any transportation charges issued by the driver.
Location: Colorado, United States
Zip/Postal Code: 80011
(Adams County)
The purchase of this item is subject to Colorado sales tax unless certain conditions are met.
Hours: 8:00 am - 5:00 pm; Mon-Fri
Call at least one day in advance to schedule pickup.
Loading Dock Available.
Driver MUST bring a copy of the IronPlanet Transportation Release to pick the item up.
Must call 2 days in advance to arrange pickup time/date.
888-433-5426
