Lower glass on right held with tape; damaged/missing seals
Seats/Armrests
Worn; stained
Seat Belts
Horn
Functional
Oil Pressure
The fault indicator shuts off after the engine oil pressure rises.
Engine Warning Lights
Functional
Travel Alarm
Functional
Gauges
Functional
Hour Meter/Odometer
Functional; 4,830 hours
- IronPlanet makes no guarantees as to actual hours/miles; we can only report what can be visually observed.
Air Conditioner
Functional
Heater
Functional
Disconnect Control
Limited Function Check (cs)
The components that were checked functioned except as noted. There is debris throughout the control station.
Hour Meter/Odometer
Engine
Engine Make and Model
Cat 3054; serial# CRS08898
Fuel Type
Diesel
Emission Control Label
US EPA certification label
Blow by @ idle (subjective observation)
Minimal
Starter
Turbo or Blower
Operational
Injector Pump
Operational
Exhaust System
Radiator
Head Gasket Leaks
None seen
Oil Leaks
None seen; residue
Fuel Leaks
None seen
Cooling System Leaks
None seen
Limited Function Check
After charging the batteries the engine started and ran during a limited check. See oil report.
Emission Control Label
Drivetrain
Operational test is limited to low speed in a confined flat area without load. Differential interlocks, full transmission shifting and functionality of all drive axles cannot be fully verified. Inspector listens for abnormal noises, observes leaks and notes physical damage.
Transmission
Torque Converter
Functional
Differential (front)
Differential (rear)
Residue
Final Drives
Limited Function Check
The drivetrain functioned during a limited check without a load. There is fluid forming on the ground from an unknown source. See oil report.
Drivetrain #1
Hydraulics
Pumps (Hydraulics)
Valves
Hoses (Hydraulics)
Worn; steel braid exposed; weathered
Cylinders
Cylinder Pins and Bushings
Worn
Limited Function Check
The hydraulic system was operational with wear during a limited check without a load.
Hydraulics #1
Chassis
IronPlanet turn-table bearing and pin connection pivot point wear inspections are limited to sound, sight and feel observations. Dial indicator testing is not performed.
Steering Linkage
Master Cylinder/Brake Control
Brake Lines/Hoses
Park Brake
Limited Function Check (Brakes)
The brake system functioned, stopping and holding the machine.
Frame Condition
Tire Size (4)
(F) 12/80-16; (R) 21L-24
Tire Condition
Cuts; gouges
Tread Depth (4 tires)
(RF) 0mm; (LF) 15mm; (RR) 12mm; (LR) 17mm
Wheel Condition
Wheel Studs, Nuts, Lugs
Some missing
Lift Arm Condition
Chassis to Arm Pins
Tilt Linkage Pins and Bushings
Bucket to Arms Pins
Limited Function Check (rt machines)
The main chassis components functioned during a limited check.
Boom Condition
Dents; scratches
Stick Condition
Dents; scratches
Stick Type
Extendable
Extendahoe Stick Guide
Visible slack
Boom Lock (Backhoe)
Inoperable; bent; loose cable
Boom Base Pin and Bushings
Worn; sealant around swing cylinder pin
Pin and Bushings Boom to Stick
Pin and Bushings Stick to Bucket
Worn
Outriggers
Street/dirt pads
Stabilizer Cylinders
Limited Function Check (Backhoe)
The main components were functional with wear during a limited check.
Chassis #1
Specialty
Backhoe / Excavator Bucket Condition
23"; worn; dents; bent; material residue; some pins replaced with wire
Backhoe / Excavator Bucket Cutting Edge
Worn
Quick Coupler
Manual; not functionally checked
Loader Bucket Cutting Edge
Reversible; turned; 2 piece
Loader Bucket Condition
93"; worn; bent; plated; welded repairs; missing tooth and pin; material residue
Specialty #1
Oil Sample Analysis
Engine
Transmission
date of analysis
Oct 16, 2009
Oct 16, 2009
Silicon
8 PPM
9 PPM
Lead
7 PPM
1 PPM
Tin
0 PPM
1 PPM
Copper
22 PPM
19 PPM
Aluminum
5 PPM
4 PPM
Silver
0 PPM
0 PPM
Nickel
1.6 PPM
0 PPM
Chromium
1 PPM
0 PPM
Iron
63 PPM
29 PPM
Glycol
NEG
N/A
Water
NEG
NEG
Fuel
<5%
N/A
Note: This condition inspection report is the result of an impartial, systematic, documented process focused on the establishment of the general, overall mechanical condition of a piece of equipment, or of a vehicle, at a specific time. The purpose of the inspection is to establish the "as-is" operational capability of the machine. It is not a performance or load test on the equipment.
Pickup Terms Failure to follow these terms may result in the seller turning away the attempt of your driver to pick up the purchased item.
Buyer will be responsible for any transportation charges issued by the driver.
Location: Colorado, United States
Zip/Postal Code: 80011
(Adams County)
The purchase of this item is subject to Colorado sales tax unless certain conditions are met.
Hours: 8:00 am - 5:00 pm; Mon-Fri
Call at least one day in advance to schedule pickup.
Loading Dock Available.
Driver MUST bring a copy of the IronPlanet Transportation Release to pick the item up.
Must call 2 days in advance to arrange pickup time/date.
888-433-5426
