Scrapes, Dents and damage; Surface rust in paint loss areas
General Appearance #1
Control Station
Steps/Ladders
The left side cat walk step is bent. The right side step is bent
Hand Rails
The handrails are bent, broken, and loose.
Mirrors
Missing
Glass
Seats/Armrests
Dirty; Burn holes; Torn cover; Damaged cushions
Seat Belts
Dirty
Horn
Inoperable
Safety lock out/stop
Inoperable
Hydraulic Controls
Loose; Damaged boots
Steering Controls
Damaged boots
Drivetrain Controls
Oil Pressure
The fault indicator shuts off after the engine oil pressure rises.
Exterior Lights Operational
No
Engine Warning Lights
The water level, hydraulic level, and the hydraulic temperature lights stay on.
Travel Alarm
Inoperable
Gauges
Functional; Some inoperable; The temp gauge is inoperable
Hour Meter/Odometer
Functional; 14,915 Hours
- IronPlanet makes no guarantees as to actual hours/miles; we can only report what can be visually observed.
Air Conditioner
Inoperable; The fan only runs on high speed.
Heater
Inoperable; The fan only runs on high speed.
Limited Function Check
The components that were checked functioned except as noted. There are loose wires in the cab. A/C & heat control knobs missing
Hour Meter/Odometer
Engine
Make and Model
Engine make: Cummins; KT19C engine; Serial #: 37138399
Fuel Type
Diesel
Emission Control Label
None found
Blow by @ idle (subjective observation)
Minimal
Starter
Turbo or Blower
Operational
Injector Pump
Operational
Exhaust System
Muffler missing
Radiator
Head Gasket Leaks
None seen
Oil Leaks
There is oil and dirt residue at the sides, rear and bottom of the engine.
Fuel Leaks
None seen
Cooling System Leaks
None seen
Limited Function Check
The engine started and ran during a limited check. See oil report.
Blow by @ idle (subjective observation)
Drivetrain
Operational test is limited to low speed in a confined flat area without load. Full transmission shifting and functionality of all drive systems cannot be fully verified. Inspector listens for abnormal noises, observes leaks and notes physical damage.
Drive Motors
Final Drives
Limited Function Check
The drivetrain functioned during a limited low speed check without a load.
Hydraulics
Pumps (Hydraulics)
Wet with residue; There is a leak at the left pump and stroke control.
Hydraulic Motors
Valves
Seepage; Wet with residue
Hydraulic Tank
Sight glass leak / seepage
Hoses (Hydraulics)
Worn; Weathered
Cylinder(s)
The bucket cylinder and the right boom cylinder are leaking.
Cylinder Pins and Bushings
Wear consistent with hours and age; Loose
Limited Function Check
The hydraulic system performed with wear and / or leaks as noted. See oil report.
Hydraulics #1
Chassis
IronPlanet pin connection pivot point wear inspections are limited to sound, sight and feel observations. Dial indicator testing is not performed.
Boom Condition
Stick Condition
Boom Base Pin and Bushings
Wear consistent with hours and age
Pin and Bushings Boom to Stick
Wear consistent with hours and age
Pin and Bushings Stick to Bucket
Wear consistent with hours and age
Stick Length
16' 6" Stick Length
Turn-table Bearing
Performs within tolerance expected for age and hours
Bottom Covers
Bent; Missing covers; Oily
Swing Motor
Roller Frames
Limited Function Check (Backhoe)
The main components were functional with visible pivot point wear.
Chassis #1
Undercarriage
Undercarriage components photos (links, bushings, sprockets, idlers, rollers, grousers) are selected as representative. Bidders are encouraged to review photos using the zoom feature to judge condition in detail.
Overall width (outside to outside of shoes)
14' 6" Overall width
Track Tensioners
See photos; Loose track; Uneven tension
Shoe Width
44" shoe width
Grouser Height Measurement
44 mm
Track link wear
See photos
Pins and Bushings Turned?
No
Pins and bushing wear
See photos
Carrier Rollers Wear
See photos
Track Rollers Wear
See photos
Front idler wear
See photos
Sprockets
Worn; See photos
Undercarriage #1
Specialty
Excavator Bucket Condition
60" Bucket; Worn; Cracked; Weld repaired; Plated; Hard surfaced
Backhoe / Excavator Bucket Shanks and Teeth
Scalloped edge between teeth
Backhoe / Excavator Bucket Shanks and Teeth
Cracked welds; The teeth are worn.
Specialty #1
Oil Sample Analysis
Engine
Hydraulic
date of analysis
Oct 21, 2009
Oct 21, 2009
Silicon
17 PPM
1 PPM
Lead
1 PPM
1 PPM
Tin
5 PPM
0 PPM
Copper
11 PPM
21 PPM
Aluminum
12 PPM
3 PPM
Silver
0 PPM
0.2 PPM
Nickel
2.4 PPM
0.1 PPM
Chromium
1.7 PPM
0.2 PPM
Iron
52 PPM
12 PPM
Glycol
NEG
N/A
Water
NEG
NEG
Fuel
<5%
N/A
Disputes:
This item is offered with IronClad Assurance® protection. With IronClad Assurance®, if a buyer discovers that the item is not substantially in the condition as represented in this inspection report, the buyer may submit a written dispute claim to IronPlanet. Following submission of a written dispute claim, IronPlanet will investigate the claim, re-inspecting the equipment item as necessary, and determine a fair and mutually beneficial resolution. Please note that IronPlanet inspections are performed solely for the purpose of reporting the visible condition of the equipment's major systems and attachments on the day of the inspection and do not include load testing or digging/lifting. These inspections are not designed nor intended to detect latent defects, or conditions that could only be found in connection with the physical dismantling of the equipment or the use of diagnostic tools or techniques. This inspection report includes ratings, comments, and photos of the various components of the item. Knowledgeable buyers are expected to carefully review all of the available information in the inspection report, including all photographs, in order to make the best bidding and buying decision possible. Please contact IronPlanet Customer Care at 888-433-5426 to file a dispute, and please review the Terms & Conditions, to which all approved bidders have agreed.
Buyer is responsible for all costs related to transporting the item.
Item must be picked up within 8 business days of the auction.
The exact item location will be provided once full payment has been received.
The buyer will have the option during Checkout to automatically receive competing quotes.
Pickup Terms Failure to follow these terms may result in the seller turning away the attempt to pick up the purchased item.
Hours: 8am-4pm M-F
You must call at least 24 hours in advance to schedule pickup
No Loading Dock, Ramps, or Forklift Available: Only RGN or trailers with ramps can be used to pick up this item at this location. Seller will not allow item to be loaded on a step-deck or flatbed trailer without the appropriate ramps.
Driver MUST bring a copy of the IronPlanet Transportation Release to pick the item up.
Call 24 hrs in advance
Within 3 business days after the auction, the buyer must submit full payment, including applicable taxes and fees.
For this item, payment is due on or before November 10.
This item is subject to 6% Kansas sales tax unless proof of exemption or declaration of Common Carrier shipment to another state is presented during item Checkout. (Read more)
Buyer must pay a transaction fee (see Buyer fees).
Payment can be made by wire transfer (recommended), certified bank check (U.S. customers only), or credit card (when full payment amount is $5,000 or less).
All bids are binding and cannot be retracted. Failure to make full payment will result in a Default Fee Penalty.
If you are looking to finance your purchase, we recommend you get
pre-approved in advance of the auction. Here are three companies we recommend
who specialize in equipment financing:
GE Capital
Thank you for your interest in applying for a GE Capital loan. GE Capital
provides equipment leasing, financing and other services to deliver significant
benefits for your business. Our products and services are customized with
flexible structure and payment terms to match your unique needs and goals. In
order to start the process of applying for a loan, please complete the attached
credit
application and forward to Bryan
Grittner or fax the application to (469) 519-4394.
Cat Financial - Capital Solutions
Get a Pre-Approved Line of Credit Be prepared for
upcoming auctions by arranging a line of credit from Cat Financial. Time is
money during an auction, and seconds count. Let Cat Financial provide you with
the pre-arranged purchasing power that lets you focus on the equipment you need.
Apply today.
Pinnacle Capital
Full Spectrum Financing for IronPlanet Auctions
IronPlanet has been offering financing for your purchases through a
partnership with Pinnacle Capital since 2002. Pinnacle knows what it takes to
get auction deals done fast and has facilitated several millions of dollars in
online purchases. Get a pre-approved line of credit set-up before you place a
bid to confirm your buying power. Click here to learn more about Pinnacle's financing products.
To qualify, complete Pinnacle's online
application. Once approved, they'll take care of the rest. Please contact
Matt Perini at 800-566-1993 or by
email to discuss the transaction further.
Powertrain Coverage. Covers major drive train components- engine, torque hubs, transmission & front
and rear axles - and more
Available in North America. May be purchased by residents of U.S. and Mexico only, for equipment operated
within U.S., Mexico or Canada.
OEM parts and service. All repairs are made by an OEM authorized repair facility with genuine OEM replacement
parts installed by OEM trained technicians.
888-433-5426
