Minor dents; scrapes; dents; broken hood bolt flange; rust in paint loss areas
Serial Number / VIN
Control Station
Steps/Ladders
Bent
Hand Rails
Mirrors
Seats/Armrests
Dirty; worn
Seat Belts
Horn
Inoperable
Disconnect Control
Hydraulic Controls
Steering Controls
Horn button is missing
Powertrain Controls
Damaged throttle control boot
Oil Pressure
PSI: 35
Exterior Lights Functional
Yes
Engine Warning Lights
Functional
Travel Alarm
Functional
Gauges
Functional
Hour Meter/Odometer
Functional; 6,210 hours
- IronPlanet makes no guarantees as to actual hours/miles; we can only report what can be visually observed.
Heater
Functional; damaged vents
Limited Function Check (cs)
The components that were checked functioned except as noted. The cup holder is missing its liner. The air intake indicator is broken.
Hour Meter/Odometer
Engine
Engine Make and Model
Cat 3046 ; Serial #5XK33936
Fuel Type
Diesel
Emission Control Label
US EPA certification label
Block Heater
No
Blow by @ idle (subjective observation)
Minimal
Starter
Turbo or Blower
Operational
Injector Pump
Operational
Exhaust System
Rusty
Radiator
Head Gasket Leaks
None Seen
Oil Leaks
None seen; residue
Fuel Leaks
None seen
Cooling System Leaks
None seen
Limited Function Check
The engine started and ran during a limited check. See oil report.
Emission Control Label
Drivetrain
Operational test is limited to low speed in a confined flat area without load. Differential interlocks, full transmission shifting and functionality of all drive axles cannot be fully verified. Inspector listens for abnormal noises, observes leaks and notes physical damage.
Travel Speeds
Variable
Final Drives
Limited Function Check (Drivetrain-Track)
The drivetrain was operational during a limited check without a load.
Hydraulics
Pumps (Hydraulics)
Valves
Hydraulic Tank
Hoses (Hydraulics)
Cylinders
Cylinder Pins and Bushings
Visible movement; Some bushings may need repair.
Limited Function Check
The hydraulic system was operational with wear during a limited check without a load. See oil report.
Hydraulics #1
Chassis
IronPlanet turn-table bearing and pin connection pivot point wear inspections are limited to sound, sight and feel observations. Dial indicator testing is not performed.
Roller Frames
Bent rock guard; missing covers
Belly pans
Dented
Limited Function Check (loader)
The main components were operational with minor wear.
Push arm/C-frame condition
Tilt/angle Linkage Pins and Bushings
Blade Trunnions/bushings
Shims remaining
Blade Lift Linkage Pins and Bushings
Limited Function Check (dozer)
The main dozer components functioned with visible wear.
Chassis #1
Undercarriage
Undercarriage components photos (links, bushings, sprockets, idlers, rollers, grousers) are selected as representative. Bidders are encouraged to review photos using the zoom feature to judge condition in detail.
Overall width (outside to outside of shoes)
95"
Track Tensioners
See Photos
Shoe Width
26"
Grouser height
24-25 mm
Track link wear
See Photos
Pins and Bushings Turned?
Yes
Pins and bushing wear
See Photos
Carrier rollers wear
See Photos
Track rollers wear
See Photos
Front idler wear
See Photos
Sprockets
See Photos
Undercarriage #1
Specialty
Blade Condition
128" width; worn; scrapes; dents; bent ears
Blade Cutting Edge Condition
Reversible-turned; worn
Drawbar
Missing pin
Specialty #1
Oil Sample Analysis
Engine
Hydraulic
date of analysis
Apr 17, 2009
Apr 17, 2009
Silicon
9 PPM
4 PPM
Lead
0 PPM
1 PPM
Tin
1 PPM
0 PPM
Copper
2 PPM
65 PPM
Aluminum
3 PPM
2 PPM
Silver
0 PPM
2.1 PPM
Nickel
0.3 PPM
0 PPM
Chromium
0.7 PPM
0 PPM
Iron
17 PPM
5 PPM
Glycol
NEG
N/A
Water
NEG
NEG
Fuel
<5%
N/A
Oil Sample Analysis
Oil sample analysis not available.
Note: This condition inspection report is the result of an impartial, systematic, documented process focused on the establishment of the general, overall mechanical condition of a piece of equipment, or of a vehicle, at a specific time. The purpose of the inspection is to establish the "as-is" operational capability of the machine. It is not a performance or load test on the equipment.
Pickup Terms Failure to follow these terms may result in the seller turning away the attempt of your driver to pick up the purchased item.
Buyer will be responsible for any transportation charges issued by the driver.
Location: North Carolina, United States
Zip/Postal Code: 28025
(Charlotte-Gastonia-Rock Hill, NC-SC area)
The purchase of this item is subject to North Carolina sales tax unless certain conditions are met.
Hours: 8:00 AM - 5:00 PM M-F
Call at least one day in advance to schedule pickup.
NO LOADING DOCK AVAILABLE: Only RGN and trailers with ramps can be used for pickup.
Driver MUST bring a copy of the IronPlanet Transportation Release to pick the item up.
888-433-5426
