There are dents, scrapes, damage, and holes on the sheet metal. There is significant rust and corrosion in the paint loss areas.
General Appearance #1
Control Station
Steps/Ladders
The right side steps are bent. The step has broken loose from the right side fender.
Hand Rails
The left side hand rails are bent.
Mirrors
Deteriorated silvering
Glass
The glass is dirty; The two rear side glasses are painted over.
Seats/Armrests
Seat Belts
Inoperable retract
Horn
Air; Functional
Hydraulic Controls
Loose
Steering Controls
Drivetrain Controls
Exterior Lights Operational
Some Inoperable; The right headlight and signal light are inoperable.
Travel Alarm
Functional
Gauges
Functional
Hour Meter/Odometer
Functional; 1,480 Hours
- IronPlanet makes no guarantees as to actual hours/miles; we can only report what can be visually observed.
Limited Function Check
The main components were functional with wear and damage as noted.
Hour Meter/Odometer (Start)
Engine
Make and Model
Cummins NTC300BC3 engine; Serial #: 60517449
Fuel Type
Diesel
Engine Brake
No
Emission Control Label
None found; Exempt
Block Heater
Yes
Blow by @ idle (subjective observation)
Minimal
Starter
Turbo or Blower
Operational
Injector Pump
Operational
Exhaust System
Rusty
Radiator
Plugging of fins; Fin damage
Head Gasket Leaks
None Seen
Oil Leaks
There is residue on the valve cover.
Fuel Leaks
None seen
Cooling System Leaks
None seen
Limited Function Check
The engine started and ran during a limited check. See oil report.
Blow by @ idle (subjective observation)
Drivetrain
Operational test is limited to low speed in a confined flat area without load. Full transmission shifting and functionality of all drive systems cannot be fully verified. Inspector listens for abnormal noises, observes leaks and notes physical damage.
Transmission
Functions but could not verify shifting in all ranges
Transmission Leaks
None Seen
Drive Line
Front Drive Axle
Leak
Rear Drive Axle
There is residue on the mid differential.
Limited Function Check (DT Vehicles)
The drivetrain was operational during a limited low speed check without a load. See oil report.
Drivetrain #1
Hydraulics
Pumps (Hydraulics)
Hydraulic Motors
Valves
Hydraulic Tank
Hoses (Hydraulics)
Weathered
Cylinder(s)
Cylinder Pins and Bushings
Minor wear
Limited Function Check
The hydraulic system was operational during a limited check without a load.
Hydraulics #1
Chassis
IronPlanet pin connection pivot point wear inspections are limited to sound, sight and feel observations. Dial indicator testing is not performed.
Steering Linkage
Steering Wheel Play
Minor
Brake Type
Air
Master Cylinder/Brake Control
Brake Lines/Hoses
Park Brake
Limited Function Check
The brake system functioned, stopping and holding the machine.
Springs/Hangers Condition
Suspension Air Bags
Drop Axles
Frame Condition
Tire Size
Size: 445/65 R 22.5; Brand: Michelin, Goodyear, Bridgestone, Yokohama
Tire Condition
Cuts
Tread Depth
RF 13 mm; LF 18 mm; RR 16 mm; RMI 16 mm; LMI 16 mm; LR 17 mm
Appears functional in a limited test of forward and reverse rotation without a load. The air cylinder at the top of the drum leaks.
Chassis #1
Oil Sample Analysis
Engine
Transmission
date of analysis
Mar 09, 2009
Mar 09, 2009
Silicon
2 PPM
3 PPM
Lead
1 PPM
22 PPM
Tin
3 PPM
1 PPM
Copper
6 PPM
107 PPM
Aluminum
2 PPM
7 PPM
Silver
0 PPM
0.2 PPM
Nickel
0.1 PPM
0.2 PPM
Chromium
0.8 PPM
0.2 PPM
Iron
15 PPM
34 PPM
Glycol
NEG
N/A
Water
NEG
NEG
Fuel
<5%
N/A
Disputes:
This item is offered with IronClad Assurance® protection. With IronClad Assurance®, if a buyer discovers that the item is not substantially in the condition as represented in this inspection report, the buyer may submit a written dispute claim to IronPlanet. Following submission of a written dispute claim, IronPlanet will investigate the claim, re-inspecting the equipment item as necessary, and determine a fair and mutually beneficial resolution. Please note that IronPlanet inspections are performed solely for the purpose of reporting the visible condition of the equipment's major systems and attachments on the day of the inspection and do not include load testing or digging/lifting. These inspections are not designed nor intended to detect latent defects, or conditions that could only be found in connection with the physical dismantling of the equipment or the use of diagnostic tools or techniques. This inspection report includes ratings, comments, and photos of the various components of the item. Knowledgeable buyers are expected to carefully review all of the available information in the inspection report, including all photographs, in order to make the best bidding and buying decision possible. Please contact IronPlanet Customer Care at 888-433-5426 to file a dispute, and please review the Terms & Conditions, to which all approved bidders have agreed.
Buyer is responsible for all costs related to transporting the item.
Item must be picked up within 8 business days of the auction.
The exact item location will be provided once full payment has been received.
The buyer will have the option during Checkout to automatically receive competing quotes.
Pickup Terms Failure to follow these terms may result in the seller turning away the attempt to pick up the purchased item.
Hours: M-F 9:00AM-4:00 PM
You must call at least 24 hours in advance to schedule pickup
No Loading Dock, Ramps, or Forklift Available: Only RGN or trailers with ramps can be used to pick up this item at this location. Seller will not allow item to be loaded on a step-deck or flatbed trailer without the appropriate ramps.
Driver MUST bring a copy of the IronPlanet Transportation Release to pick the item up.
Call before pick-up @ 919-730-5789
Within 3 business days after the auction, the buyer must submit full payment, including applicable taxes and fees.
This item is subject to 8% North Carolina sales tax unless proof of exemption or declaration of Common Carrier shipment to another state is presented during item Checkout. (Read more)
Buyer must pay a transaction fee (see Buyer fees).
Payment can be made by wire transfer (recommended), certified bank check (U.S. customers only), or credit card (when full payment amount is $5,000 or less).
A transferable title will be sent to the buyer by express mail or similar service within 15 business days of the auction. Buyer is responsible for vehicle registration.
All bids are binding and cannot be retracted. Failure to make full payment will result in a Default Fee Penalty.
If you are looking to finance your purchase, we recommend you get
pre-approved in advance of the auction. Here are three companies we recommend
who specialize in equipment financing:
GE Capital
Thank you for your interest in applying for a GE Capital loan. GE Capital
provides equipment leasing, financing and other services to deliver significant
benefits for your business. Our products and services are customized with
flexible structure and payment terms to match your unique needs and goals. In
order to start the process of applying for a loan, please complete the attached
credit
application and forward to Bryan
Grittner or fax the application to (469) 519-4394.
Cat Financial - Capital Solutions
Get a Pre-Approved Line of Credit Be prepared for
upcoming auctions by arranging a line of credit from Cat Financial. Time is
money during an auction, and seconds count. Let Cat Financial provide you with
the pre-arranged purchasing power that lets you focus on the equipment you need.
Apply today.
Pinnacle Capital
Full Spectrum Financing for IronPlanet Auctions
IronPlanet has been offering financing for your purchases through a
partnership with Pinnacle Capital since 2002. Pinnacle knows what it takes to
get auction deals done fast and has facilitated several millions of dollars in
online purchases. Get a pre-approved line of credit set-up before you place a
bid to confirm your buying power. Click here to learn more about Pinnacle's financing products.
To qualify, complete Pinnacle's online
application. Once approved, they'll take care of the rest. Please contact
Matt Perini at 800-566-1993 or by
email to discuss the transaction further.
Powertrain Coverage. Covers major drive train components- engine, torque hubs, transmission & front
and rear axles - and more
Available in North America. May be purchased by residents of U.S. and Mexico only, for equipment operated
within U.S., Mexico or Canada.
OEM parts and service. All repairs are made by an OEM authorized repair facility with genuine OEM replacement
parts installed by OEM trained technicians.
888-433-5426
You must be a Vehicle Dealer to purchase this vehicle in California.
