Enclosed Cab, A/C, Heater, Komatsu Diesel Engine, Autoshift Transmission, 4x4, Onboard Weigh Scales, 2,950mm GP Bucket, 26.5R25, CE certificate available from seller - CE mark on machine
Meter Reading:
11,517 Hours
Serial Number:
Location:
Nord-Pas-de-Calais, France
Shipping:
See shipping details for important pickup requirements and to get a shipping estimate
Inspection Report :
Protected by IronClad Assurance
Payment:
Payment due within 3 business days after auction. See Details
CE certificate available from seller - CE mark on machine
Paint
See photos for condition
Sheet Metal (fiberglass) Condition
See photos for condition
Steps/Ladders
Right side steps are bent have weld repairs.
Hand Rails
See photos for condition
General Appearance #1
Control Station
Mirrors
Left side cracked
Glass
Seats/Armrests
See photos for condition; Torn cover
Seat Belts
Not equipped
Horn
Inoperable
Control Lock Lever
Hydraulic Controls
Lever buttons are damaged
Steering Controls
Drivetrain Controls
The machine would not change gear in Automatic mode. Manual Powershift works well.
Oil Pressure
The fault indicator shuts off after the engine oil pressure rises.
Exterior Lights Operational
Some inoperable
Warning Lights
Operational; E03 warning is on Display and E01 Entretien.
Travel Alarm
Operational
Gauges
Operational
Hour Meter/Odometer
11,517 Hours; Operational hour meter
- IronPlanet makes no guarantees as to actual hours/miles; we can only report what can be visually observed.
Air Conditioner
Cool but not cold
Heater
Operational
Limited Function Check
The main components operated except as noted.; All of the switch labels have worn, Therefore is difficult to know which switch does what.
Hour Meter/Odometer (Start)
Engine
Make and Model
Komatsu; SAA6D125E-3 engine; Serial #: Family 2KLXL11.0004
Fuel Type
Diesel
Emission Control Label
Both EC and US EPA certification label
Blow by @ idle (subjective observation)
Minor
Starter
Operational
Turbo or Blower
Operational; Exhaust connection leak
Fuel System
Operational
Exhaust System
See photos for condition; Rusty
Radiator
Difficult to access
Oil Leaks
None seen
Fuel Leaks
None seen
Cooling System Leaks
None seen
Limited Function Check
The engine started and ran. See oil report.
Emission Control Label
Drivetrain
Operational test is limited to low speed in a confined flat area without load. Differential interlocks, full transmission shifting and functionality of all drive axles cannot be fully verified. Inspector listens for abnormal noises, observes leaks and notes physical damage.
Transmission
Manual powershift works well Autoshift system did not respond to the controls.
Front Drive Axle
Rear Drive Axle
Final Drives
Limited Function Check
The drivetrain was operational.
Drivetrain #1
Hydraulics
Pumps (Hydraulics)
Valves
Hydraulic Tank
Weld repair; New bracket has been fitted
Hoses (Hydraulics)
Loader Lift Cylinders
Fluid accumulation on the right cylinder; Minor to moderate pin and bushing movement
Bucket Tilt Cylinders
Minor to moderate pin and bushing movement
Steering Cylinders
Minor to moderate pin and bushing movement
Limited Function Check
The hydraulic system was operational without a load.
Hydraulics #1
Chassis
IronPlanet pin connection pivot point wear inspections are limited to sound, sight and feel observations. Dial indicator testing is not performed.
Steering Linkage
Articulating Center Pins
Steering Wheel Play
Minor to moderate movement
Brake Type
Hydraulic
Master Cylinder
Park Brake
Held on slope
Limited Function Check
The brake system functioned, stopping and holding the machine.
Frame Condition
Bracket welded to frame at right side step,
Tire Size
26.5R25 front tires; 26.5R25 rear tires; Bridgestone; Brand name
Tire Condition
See photos; Cuts; Gouges; Right side tires have more wear. Cracks in side walls
Wheel Condition
Wheel Studs, Nuts, Lugs
Lift Arm Condition
Chassis to Arm Pins
Tilt Linkage Pins and Bushings
Angle iron has been welded on top of the small tilt linkage. Weld repair on the lower section of the main link (see photos).
Bucket to Arm Pins
Minor to moderate movement
Limited Function Check
The main components were operational with movement as indicated.
Chassis #1
Specialty
Loader Bucket Condition
2,950mm General purpose loader bucket
Loader Bucket Cutting Edge
Worn/damaged edge; Heavy wear on the right side of the cutting edge.
Drawbar
Scales
Not functionally tested
Specialty #1
Oil Sample Analysis
Engine
date of analysis
Jun 10, 2012
Silicon
4 PPM
Lead
2 PPM
Tin
0 PPM
Copper
2 PPM
Aluminum
1 PPM
Silver
N/A
Nickel
0 PPM
Chromium
0.6 PPM
Iron
16 PPM
Glycol
0
Water
0
Fuel
N/A
Disputes:
This item is offered with IronClad Assurance® protection. With IronClad Assurance®, if a buyer discovers that the item is not substantially in the condition as represented in this inspection report, the buyer may submit a written dispute claim to IronPlanet. Following submission of a written dispute claim, IronPlanet will investigate the claim, re-inspecting the equipment item as necessary, and determine a fair and mutually beneficial resolution. Please note that IronPlanet inspections are performed solely for the purpose of reporting the visible condition of the equipment''s major systems and attachments on the day of the inspection and do not include load testing or digging/lifting. These inspections are not designed nor intended to detect latent defects, or conditions that could only be found in connection with the physical dismantling of the equipment or the use of diagnostic tools or techniques. This inspection report includes ratings, comments, and photos of the various components of the item. Knowledgeable buyers are expected to carefully review all of the available information in the inspection report, including all photographs, in order to make the best bidding and buying decision possible.
Buyer is responsible for all costs related to transporting the item.
Item must be picked up within 8 business days of the auction, or the buyer will incur storage charges.
The location information will be provided once full payment has been received.
Pickup Terms Failure to follow these terms may result in the seller turning away the attempt to pick up the purchased item.
Hours: 8:00 - 12:00 / 14:00 - 17:00 hrs
Please check loading facilities' suitability directly with seller; call at least 24 hrs in advance
Loading Dock Available
Ramps NOT Available
Forklift Available
Driver MUST bring a copy of the IronPlanet Transportation Release to pick the item up.
Within 3 business days after the auction, the buyer must submit full payment, including applicable taxes and fees.
For this item, payment is due on or before July 2.
Buyer must pay a transaction fee, based on the final selling price:
Final Selling Price
Transaction Fee
€1 to €3,000
10% of the final selling price
€3,000 to €32,500
3% of the final selling price (min €300)
Above €32,500
€975
Payment can be made by wire transfer (recommended), certified bank check (U.S. customers only), or credit card (when full payment amount is $5,000 or less).
All bids are binding and cannot be retracted. Failure to make full payment will result in a Default Fee.
If you are looking to finance your purchase, we recommend you get pre-approved in advance of the auction. Here is a company we recommend who specialize in equipment financing:
Cat Financial
Financing for the way you work Your business is always changing, and so are your financial needs. You need quality equipment to get your work done and financing solutions that make sense for you. Count on a company that understands the work you do.
Warranty by Premium 2000
