Enclosed Cab, A/C, Heater, Komatsu Diesel Engine, Power shift Transmission,Autoshift , 3rd Valve , Hydraulic Coupler, GP Bucket, 20,5R25 Tires, No CE certificate available from seller - CE mark on machine,
Meter Reading:
11,927 Hours
Serial Number:
Location:
Malmohus, Sweden
Shipping:
See shipping details for important pickup requirements and to get a shipping estimate
Inspection Report :
Protected by IronClad Assurance
Payment:
Payment due within 3 business days after auction. See Details
No CE certificate available from seller - CE mark on machine
Paint
Not original paint; See photos for condition
Sheet Metal (fiberglass) Condition
Minor dents; Scrapes; Surface rust in areas; Missing panels; See photos for condition; Rear wheel covers.
Steps/Ladders
See photos for condition
Hand Rails
See photos for condition
General Appearance #1
Control Station
Mirrors
Cracked; Right side.
Glass
See photos for condition
Seats/Armrests
Burn holes; See photos for condition
Seat Belts
Operational
Horn
Operational
Control Lock Lever
Hydraulic Controls
Controls Stick
3rd Valve
Equipped with a 3rd valve and plumbing for an auxiliary attachment.
Steering Controls
Drivetrain Controls
Controls stick
Oil Pressure
The fault indicator shuts off after the engine oil pressure rises.
Exterior Lights Operational
Yes; Some inoperable
Engine Warning Lights
Operational
Gauges
Operational
Hour Meter/Odometer
11927,5 Hours; Operational hour meter
- IronPlanet makes no guarantees as to actual hours/miles; we can only report what can be visually observed.
Air Conditioner
Operational
Heater
Operational
Limited Function Check
The main components are in place and operational.
3rd Valve
Engine
Make and Model
Komatsu; S6D11AE-1 engine; Serial #: 21296579; 6 Cylinder Engine
Fuel Type
Diesel
Emission Control Label
None found
Blow by @ idle (subjective observation)
Minor
Starter
Operational
Turbo or Blower
Operational
Fuel System
Operational
Exhaust System
No visible damage; See photos for condition
Radiator
Minor plugging of fins
Oil Leaks
None seen; See photos
Fuel Leaks
None seen; See photos
Cooling System Leaks
None seen; See photos
Limited Function Check
The engine started and ran.
Blow by @ idle (subjective observation)
Drivetrain
Operational test is limited to low speed in a confined flat area without load. Differential interlocks, full transmission shifting and functionality of all drive axles cannot be fully verified. Inspector listens for abnormal noises, observes leaks and notes physical damage.
Transmission
Operational
Transmission Disconnect
Operational
Front Drive Axle
Rear Drive Axle
Final Drives
Limited Function Check
The drivetrain was operational.
Drivetrain #1
Hydraulics
Pumps (Hydraulics)
Fluid accumulation
Valves
Fluid accumulation
Hydraulic Tank
Low oil level
Hoses (Hydraulics)
Loader Lift Cylinders
Fluid accumulation on the left cylinder; Fluid accumulation on the right cylinder; Minor pin and bushing movement
Bucket Tilt Cylinders
Minor pin and bushing movement
Steering Cylinders
Fluid accumulation on the left cylinder; Fluid accumulation on the right cylinder; Minor pin and bushing movement
Limited Function Check
The hydraulic system was operational without a load.A valve is discounted under cab, Function unknown.
Hydraulics #1
Chassis
IronPlanet pin connection pivot point wear inspections are limited to sound, sight and feel observations. Dial indicator testing is not performed.
Steering Linkage
Minimal movement
Articulating Center Pins
Minimal movement
Steering Wheel Play
Minimal movement
Brake Type
Hydraulic
Master Cylinder
Brake Lines/Hoses
Not operationally checked
Park Brake
Held against power
Limited Function Check
The brake system functioned, stopping and holding the machine.
Frame Condition
Surface Rust
Tire Size
20,5R25 front tires; Goodyear
Tire Condition
See photos; Cuts
Wheel Condition
Rusty
Wheel Studs, Nuts, Lugs
Lift Arm Condition
Chassis to Arm Pins
Minimal movement
Tilt Linkage Pins and Bushings
Minimal movement
Quick Coupler to Arms Pins
Minor to moderate movement
Limited Function Check
The main chassis components were operational in a limited check.
Chassis #1
Specialty
Loader Bucket Condition
2500mm General purpose loader bucket; Worn
Loader Bucket Cutting Edge
Loader Quick Coupler
Hydraulic coupler operational
Drawbar
Specialty #1
Disputes:
This item is offered with IronClad Assurance® protection. With IronClad Assurance®, if a buyer discovers that the item is not substantially in the condition as represented in this inspection report, the buyer may submit a written dispute claim to IronPlanet. Following submission of a written dispute claim, IronPlanet will investigate the claim, re-inspecting the equipment item as necessary, and determine a fair and mutually beneficial resolution. Please note that IronPlanet inspections are performed solely for the purpose of reporting the visible condition of the equipment''s major systems and attachments on the day of the inspection and do not include load testing or digging/lifting. These inspections are not designed nor intended to detect latent defects, or conditions that could only be found in connection with the physical dismantling of the equipment or the use of diagnostic tools or techniques. This inspection report includes ratings, comments, and photos of the various components of the item. Knowledgeable buyers are expected to carefully review all of the available information in the inspection report, including all photographs, in order to make the best bidding and buying decision possible.
Buyer is responsible for all costs related to transporting the item.
Item must be picked up within 8 business days of the auction, or the buyer will incur storage charges.
The location information will be provided once full payment has been received.
Pickup Terms Failure to follow these terms may result in the seller turning away the attempt to pick up the purchased item.
Hours: 8am - 4pm Mon - Fri
Yes, call before pick up minimum 48hrs before collection
Loading Dock NOT Available
Ramps Available
Forklift NOT Available
Driver MUST bring a copy of the IronPlanet Transportation Release to pick the item up.
Within 3 business days after the auction, the buyer must submit full payment, including applicable taxes and fees.
For this item, payment is due on or before June 5.
Buyer must pay a transaction fee, based on the final selling price:
Final Selling Price
Transaction Fee
€1 to €3,000
10% of the final selling price
€3,000 to €32,500
3% of the final selling price (min €300)
Above €32,500
€975
Payment can be made by wire transfer (recommended), certified bank check (U.S. customers only), or credit card (when full payment amount is $5,000 or less).
All bids are binding and cannot be retracted. Failure to make full payment will result in a Default Fee.
If you are looking to finance your purchase, we recommend you get pre-approved in advance of the auction. Here is a company we recommend who specialize in equipment financing:
Cat Financial
Financing for the way you work Your business is always changing, and so are your financial needs. You need quality equipment to get your work done and financing solutions that make sense for you. Count on a company that understands the work you do.
Warranty by Premium 2000
