Enclosed Cab, A/C, Heater, Cummin Diesel Engine, Powershift Transmission, Push Block, Ripper, Blade, 17.5x25 Tyres. No CE certificate available from seller - No CE mark on machine.
Meter Reading:
419 Hours
Serial Number:
Location:
DOHA, Qatar
Shipping:
See shipping details for important pickup requirements and to get a shipping estimate
Inspection Report :
Protected by IronClad Assurance
Payment:
Payment due within 3 business days after auction. See Details
No CE certificate available from seller - No CE mark on machine
Paint
See photos for condition; Scratches; Chips
Sheet Metal (fiberglass) Condition
Cracks; See photos for condition
Steps/Ladders
No visible damage; See photos for condition
Hand Rails
No visible damage; See photos for condition
General Appearance #1
Control Station
Mirrors
Left side mirror missing.
Glass
Seats/Armrests
Torn cover; Damaged cushion; See photos for condition
Seat Belts
Operational
Horn
Operational
Hydraulic Controls
Steering Control
Drivetrain Controls
Oil Pressure
No oil pressure indicator
Exterior Lights Operational
Yes
Warning Lights
Operational
Travel Alarm
Operational
Gauges
Operational
Hour Meter/Odometer
419 Hours; Inoperable hour meter
- IronPlanet makes no guarantees as to actual hours/miles; we can only report what can be visually observed.
Air Conditioner
Does not cool
Heater
Operational
Limited Function Check (cs)
The main components operated except as noted.
Hour Meter/Odometer
Engine
Make and Model
Cummins; 6 Cylinder Engine
Fuel Type
Diesel
Emission Control Label
None found
Blow by @ idle (subjective observation)
Minor
Starter
Operational
Turbo or Blower
Operational
Fuel System
Operational
Exhaust System
Rust penetration; See photos for condition
Radiator
Fin damage
Oil Leaks
None seen; See photos
Fuel Leaks
None seen; See photos
Cooling System Leaks
None seen; See photos
Limited Function Check (Engine)
The engine started and ran.
A/C Compressor
Drivetrain
Operational test is limited to low speed in a confined flat area without load. Differential interlocks, full transmission shifting and functionality of all drive axles cannot be fully verified. Inspector listens for abnormal noises, observes leaks and notes physical damage.
Transmission Type (Motorgrader)
Powershift
Transmission
Operational
Rear Tandems (Chain Drives)
Limited Function Check
The drivetrain was operational.
Drivetrain #1
Hydraulics
Pumps (Hydraulics)
Valves
Hydraulic Tank
Hoses (Hydraulics)
Hydraulic Motors
Steering Cylinders
Rust pitting in the chrome on the right cylinder; Minimal pin and bushing movement
Articulation Cylinders
Minimal pin and bushing movement
Wheel Lean Cylinders
Rust pitting in the chrone on the right cylinder; Minimal pin and bushing movement
Blade Lift Cylinders
Minimal pin and bushing movement
Blade Angle Cylinders
Minimal pin and bushing movement
Blade Side Shift Cylinders
Rust pitting in the chrome on the right cylinder; Minimal pin and bushing movement
Saddle Lock Pin
Limited Function Check
The hydraulic system was operational without a load.
Hydraulics #1
Chassis
IronPlanet pin connection pivot point wear inspections are limited to sound, sight and feel observations. Dial indicator testing is not performed.
Blade Tilt Frame (saddle)
Y-frame
Y-frame Pivot Trunnion
Minimal movement
Circle Frame and Brackets
Circle Wear Strips
Circle Support Brackets
Circle Gear Box
Minor wear
Circle Gear
Minor wear
Mold Board Slide Wear Strips
Articulating Center Pins Wear
Minimal movement
Front Axle Oscillating Pin Wear
Minimal movement
Steering Linkage
Minimal movement
Steering Wheel Play
Minimal movement
Wheel Tilt Linkage
See photos for condition of rubber boots.
Limited Function Check (grader)
The main chassis components were operational in a limited check.
Brake Type (Motorgrader)
Air over hydraulic
Master Cylinder/Brake Control
Brake Lines/Hoses
Park Brake
Stopped the machine while rolling; Would not hold against power; Unable to test with slope; did not completely release.
Limited Function Check
The service brakes performed. The park brake would not hold the machine.
Frame Condition
Tire Size
17.5x25 tires
Tire Condition
See photos; Cuts; Gouges
Wheel Condition
Wheel Studs, Nuts, Lugs
Chassis #1
Specialty
Blade Condition
Blade Cutting Edge Condition (MG)
Worn; Reversible not turned.
Ripper Condition
Specialty #1
Disputes:
This item is offered with IronClad Assurance® protection. With IronClad Assurance®, if a buyer discovers that the item is not substantially in the condition as represented in this inspection report, the buyer may submit a written dispute claim to IronPlanet. Following submission of a written dispute claim, IronPlanet will investigate the claim, re-inspecting the equipment item as necessary, and determine a fair and mutually beneficial resolution. Please note that IronPlanet inspections are performed solely for the purpose of reporting the visible condition of the equipment''s major systems and attachments on the day of the inspection and do not include load testing or digging/lifting. These inspections are not designed nor intended to detect latent defects, or conditions that could only be found in connection with the physical dismantling of the equipment or the use of diagnostic tools or techniques. This inspection report includes ratings, comments, and photos of the various components of the item. Knowledgeable buyers are expected to carefully review all of the available information in the inspection report, including all photographs, in order to make the best bidding and buying decision possible.
Buyer is responsible for all costs related to transporting the item.
Item must be picked up within 8 business days of the auction, or the buyer will incur storage charges.
The location information will be provided once full payment has been received.
Pickup Terms Failure to follow these terms may result in the seller turning away the attempt to pick up the purchased item.
Hours: 8am to 4:30pm
You must call at least 24 hours in advance to schedule pickup
Loading Dock Available
Ramps Available
Forklift Available
Driver MUST bring a copy of the IronPlanet Transportation Release to pick the item up.
Within 3 business days after the auction, the buyer must submit full payment, including applicable taxes and fees.
For this item, payment is due on or before August 28.
Buyer must pay a transaction fee, based on the final selling price:
Final Selling Price
Transaction Fee
$1 to $5,000
10% of the final selling price
$5,000 to $31,800
3.85% of the final selling price (min $500)
Above $31,800
$1,225
Payment can be made by wire transfer (recommended), certified bank check (U.S. customers only), or credit card (when full payment amount is $5,000 or less).
All bids are binding and cannot be retracted. Failure to make full payment will result in a Default Fee.
If you are looking to finance your purchase, we recommend you get pre-approved in advance of the auction. Here is a company we recommend who specialize in equipment financing:
Cat Financial
Financing for the way you work Your business is always changing, and so are your financial needs. You need quality equipment to get your work done and financing solutions that make sense for you. Count on a company that understands the work you do.
Warranty by Premium 2000
