Enclosed Cab, Heater, Passenger seat, Deutz TD226B-6 Engine, Manual Transmission w/Shuttle Lever, Partial Powershift, Exterior 3-Point Hitch Controls, 540 rpm PTO (6 splines), Front Mount PTO, 480/70R34 Front Tires, 20,8R42 Rear Tires, Rear Remote Hydraulic Circuits, 3-Point Hitch, Front 3-Point Hitch, No CE certificate available from seller - No CE mark on machine
Meter Reading:
5,070 Hours
Serial Number:
Location:
Aarhus, Denmark
Shipping:
See shipping details for important pickup requirements and to get a shipping estimate
Inspection Report :
Protected by IronClad Assurance
Payment:
Payment due within 3 business days after auction. See Details
No CE certificate available from seller - No CE mark on machine
Paint
Scratches; See photos for condition
Sheet Metal (Fiberglass) Condition
Minor dents/scratches; Surface rust; See photos for condition; Metal corrosion
Steps/Ladders
See photos for condition
Hand Rails
See photos for condition
General Appearance #1
Control Station
Mirrors
Cracked; Scratched; Missing
Glass
See photos for condition
Seats/Armrests
See photos for condition
Passenger seat
See photos for condition
Horn
Operational
Control Lock Lever
Hydraulic Controls
Steering Controls
Minimal steering wheel play
Drivetrain Controls
Controls stick
Oil Pressure
The fault indicator shuts off after the engine oil pressure rises.
Exterior Lights Operational
Yes; Some inoperable
Engine Warning Lights
Operational
Gauges
Inoperable gauges: Revs.; Some gauges inoperable
Hour Meter/Odometer
5070 Hours; Inoperable hour meter, Another hour meter reads 85 hrs
- IronPlanet makes no guarantees as to actual hours/miles; we can only report what can be visually observed.
Air Conditioner
Operational
Heater
Operational
Limited Function Check
The main components operated except as noted.
Hour Meter/Odometer (Start)
Engine
Fuel Type
Diesel
Emission Control Label
None found
Blow by @ idle (subjective observation)
Minor
Starter
Operational
Turbo or Blower
Operational
Fuel System
Operational
Exhaust System
No visible damage; See photos for condition
Radiator
Minor plugging of fins
Oil Leaks
None seen; See photos
Fuel Leaks
None seen; See photos
Cooling System Leaks
None seen; See photos
Limited Function Check
After jump starting, the engine ran. The engine would not re-start after shutting down without jump starting. See oil report.
Blow by @ idle (subjective observation)
Drivetrain
Operational test is limited to low speed in a confined flat area without load. Differential interlocks, full transmission shifting and functionality of all drive axles cannot be fully verified. Inspector listens for abnormal noises, observes leaks and notes physical damage.
Transmission
Operational
Clutch
Engages
Front Drive Axle
Rear Drive Axle
Will not let diff. lock go!
Final Drives
PTO
Functional; 540 rpm (6 splines)
Front Axle Configuration
Rigid mount with fixed pivot point
Limited Function Check
The drivetrain was operational.
Drivetrain #1
Chassis
IronPlanet pin connection pivot point wear inspections are limited to sound, sight and feel observations. Dial indicator testing is not performed.
Steering Linkage
Minimal movement
Steering Wheel Play
Minimal movement
Frame Condition
Rusty
Limited Function Check
The main chassis components were operational in a limited check.
Brake Type
Hydraulic
Master Cylinder/Brake Control
Brake Lines/Hoses
Not operationally checked
Park Brake
Inoperable
Limited Function Check
The service brakes performed. The park brake would not hold the machine.
Tire Size
480/70R34 Front tires; 20,8R42 Rear tires; LF Agrimax; LR Goodyear
Tire Condition
Minor cuts and gouges
Tread Depth
LF 35mm ;LR 38mm ; LFI 28mm; LFO 25mm
Wheel Condition
Rusty
Wheel Studs
Chassis #1
Hydraulics
Pumps (Hydraulics)
Number of Hydraulic Circuits
Rear: 4
Rear Remote Hydraulic Circuits
Functional
Trailer Brake Connnection
Yes
Valves
Fluid accumulation
Hydraulic Tank
Hoses (Hydraulics)
Weathered
Cylinder(s)
Rod chrome damage
Cylinder Pins and Bushings
Minor to moderate movement
Limited Function Check
The hydraulic system was operational without a load.
Hydraulics #1
Specialty
3-Point Linkage
Front 3-Point Linkage
Drawbar
Pin holes worn
Specialty #1
Oil Sample Analysis
Engine
date of analysis
Jul 13, 2012
Silicon
11 PPM
Lead
3 PPM
Tin
1 PPM
Copper
1 PPM
Aluminum
3 PPM
Silver
N/A
Nickel
0 PPM
Chromium
1.4 PPM
Iron
19 PPM
Glycol
0
Water
0
Fuel
N/A
Disputes:
This item is offered with IronClad Assurance® protection. With IronClad Assurance®, if a buyer discovers that the item is not substantially in the condition as represented in this inspection report, the buyer may submit a written dispute claim to IronPlanet. Following submission of a written dispute claim, IronPlanet will investigate the claim, re-inspecting the equipment item as necessary, and determine a fair and mutually beneficial resolution. Please note that IronPlanet inspections are performed solely for the purpose of reporting the visible condition of the equipment''s major systems and attachments on the day of the inspection and do not include load testing or digging/lifting. These inspections are not designed nor intended to detect latent defects, or conditions that could only be found in connection with the physical dismantling of the equipment or the use of diagnostic tools or techniques. This inspection report includes ratings, comments, and photos of the various components of the item. Knowledgeable buyers are expected to carefully review all of the available information in the inspection report, including all photographs, in order to make the best bidding and buying decision possible.
Buyer is responsible for all costs related to transporting the item.
Item must be picked up within 8 business days of the auction, or the buyer will incur storage charges.
The location information will be provided once full payment has been received.
Pickup Terms Failure to follow these terms may result in the seller turning away the attempt to pick up the purchased item.
Hours: 7am to 4pm
No
Loading Dock Available
Ramps Available
Forklift Available
Driver MUST bring a copy of the IronPlanet Transportation Release to pick the item up.
Within 3 business days after the auction, the buyer must submit full payment, including applicable taxes and fees.
For this item, payment is due on or before November 5.
Buyer must pay a transaction fee, based on the final selling price:
Final Selling Price
Transaction Fee
€1 to €3,000
10% of the final selling price
€3,000 to €32,500
3% of the final selling price (min €300)
Above €32,500
€975
Payment can be made by wire transfer (recommended), certified bank check (U.S. customers only), or credit card (when full payment amount is $5,000 or less).
All bids are binding and cannot be retracted. Failure to make full payment will result in a Default Fee.
If you are looking to finance your purchase, we recommend you get pre-approved in advance of the auction. Here is a company we recommend who specialize in equipment financing:
Cat Financial
Financing for the way you work Your business is always changing, and so are your financial needs. You need quality equipment to get your work done and financing solutions that make sense for you. Count on a company that understands the work you do.
Warranty by Premium 2000
