Minor dents/scratches; Dents; Cracks; Surface rust; Damaged sheet metal; Weld repair; See photos for condition
Steps/Ladders
See photos for condition
Hand Rails
See photos for condition
General Appearance #1
Control Station
Mirrors
Glass
The left glass is cracked.
Seats/Armrests
Seat Belts
Operational
Horn
Operational
Control Lock Lever
Hydraulic Controls
Steering Control
Drivetrain Controls
Oil Pressure
The fault indicator shuts off after the engine oil pressure rises.
Exterior Lights Operational
Some inoperable; Some missing; Some damaged
Warning Lights
Some inoperable
Travel Alarm
Operational
Gauges
Operational
Hour Meter/Odometer
18,809 Hours; Operational hour meter
- IronPlanet makes no guarantees as to actual hours/miles; we can only report what can be visually observed.
Heater
Operational
Limited Function Check (cs)
The main components operated except as noted.
Hour Meter/Odometer
Engine
Make and Model
Caterpillar 8 Cylinder Engine
Fuel Type
Diesel
Emission Control Label
None found
Blow by @ idle (subjective observation)
Significant
Starter
Operational
Turbo or Blower
Operational
Fuel System
Operational
Exhaust System
See photos for condition
Radiator
Minor plugging of fins; Damaged fins
Oil Leaks
Fluid accumulation on the side of the engine
Fuel Leaks
None seen
Cooling System Leaks
There is an antifreeze leak at the front of the engine from an unknown source.
Limited Function Check (Engine)
The engine started and ran with smoke that mostly cleared. See oil report.
Blow by @ idle (subjective observation)
Drivetrain
Operational test is limited to low speed in a confined flat area without load. Differential interlocks, full transmission shifting and functionality of all drive axles cannot be fully verified. Inspector listens for abnormal noises, observes leaks and notes physical damage.
Transmission
Operational
Travel Speeds
3
Steering Clutches
Steering Brakes
Service Brakes
Final Drives
Limited Function Check (Drivetrain-Track)
The drivetrain was operational without a load. See oil report.
Drivetrain #1
Hydraulics
Pumps (Hydraulics)
Valves
Hydraulic Tank
Hoses (Hydraulics)
The blade cylinder hoses are worn.
Blade Lift Cylinders
Seepage on the right cylinder; Heavy pin and bushing movement
Blade Angle Cylinders
Minor to moderate pin and bushing movement
Ripper Cylinders
Fluid accumulation on the left cylinder; Minor to moderate pin and bushing movement
Limited Function Check
The hydraulic system was operational without a load. See oil report.
Hydraulics #1
Chassis
IronPlanet pin connection pivot point wear inspections are limited to sound, sight and feel observations. Dial indicator testing is not performed.
Frame Condition
Roller Frames
Belly pans
Pivot Shafts
Equalizer Bar Pivot Points
Wear consistent with hours and age
Limited Function Check (Chassis)
The main components were operational when checked without a load. Wire wrapped around the inside of the final drive
Push Arm/C-Frame Condition
Cracked; Weld repair
Push Arm Pivot/C-FrameTrunnions
Minor to moderate movement; Shims remaining
Tilt Linkage Pins and Bushings
Minor to moderate movement
Blade Trunnions/bushings
Heavy movement
Limited Function Check (dozer)
The main components were operational in a limited check.
Chassis #1
Undercarriage
Undercarriage components photos (links, bushings, sprockets, idlers, rollers, grousers) are selected as representative. Bidders are encouraged to review photos using the zoom feature to judge condition in detail.
Overall width (outside to outside of shoes)
9' 4 1/2" Overall width
Track Tensioners
See photos for condition
Shoe Width
24" track shoes
Grouser Height
Left Side: 34 mm; Right Side: 35 mm
Track link wear
See photos for condition
Pins and Bushings Turned?
No
Pins and bushing wear
See photos for condition
Track Rollers Wear
See photos for condition; Damaged
Idlers
See photos for condition; Chipped
Sprockets
See photos for condition
Pins and bushing wear
Specialty
Blade Condition
14' 10" blade; Worn; Dented; Hole; Weld repair
Blade Cutting Edge Condition
The outside edges are turned, but the center edge is not.
Ripper Condition
Specialty #1
Oil Sample Analysis
Engine
Transmission
Hydraulic
date of analysis
Jun 19, 2012
Jun 19, 2012
Jun 19, 2012
Silicon
14 PPM
9 PPM
7 PPM
Lead
1 PPM
0 PPM
4 PPM
Tin
1 PPM
0 PPM
1 PPM
Copper
12 PPM
13 PPM
65 PPM
Aluminum
4 PPM
1 PPM
3 PPM
Silver
0 PPM
0 PPM
0.2 PPM
Nickel
1.3 PPM
0.2 PPM
0.3 PPM
Chromium
1 PPM
0.3 PPM
0.3 PPM
Iron
36 PPM
6 PPM
28 PPM
Glycol
NEG
N/A
N/A
Water
NEG
NEG
NEG
Fuel
<5%
N/A
N/A
Disputes:
This item is offered with IronClad Assurance® protection. With IronClad Assurance®, if a buyer discovers that the item is not substantially in the condition as represented in this inspection report, the buyer may submit a written dispute claim to IronPlanet. Following submission of a written dispute claim, IronPlanet will investigate the claim, re-inspecting the equipment item as necessary, and determine a fair and mutually beneficial resolution. Please note that IronPlanet inspections are performed solely for the purpose of reporting the visible condition of the equipment''s major systems and attachments on the day of the inspection and do not include load testing or digging/lifting. These inspections are not designed nor intended to detect latent defects, or conditions that could only be found in connection with the physical dismantling of the equipment or the use of diagnostic tools or techniques. This inspection report includes ratings, comments, and photos of the various components of the item. Knowledgeable buyers are expected to carefully review all of the available information in the inspection report, including all photographs, in order to make the best bidding and buying decision possible.
Buyer is responsible for all costs related to transporting the item.
Item must be picked up within 8 business days of the auction, or the buyer will incur storage charges.
The location information will be provided once full payment has been received.
The buyer will have the option during Checkout to automatically receive competing quotes.
Pickup Terms Failure to follow these terms may result in the seller turning away the attempt to pick up the purchased item.
Hours: 9am to 4pm, Mon-Fri
Call 48 hours in advance for appointment and ask for directions.
No Loading Dock, Ramps, or Forklift Available: Only RGN or trailers with ramps can be used to pick up this item at this location. Seller will not allow item to be loaded on a step-deck or flatbed trailer without the appropriate ramps.
Driver MUST bring a copy of the IronPlanet Transportation Release to pick the item up.
Within 3 business days after the auction, the buyer must submit full payment, including applicable taxes and fees.
For this item, payment is due on or before July 17.
This item is subject to Utah sales tax. (Read more)
Buyer must pay a transaction fee, based on the final selling price:
Final Selling Price
Transaction Fee
$1 to $5,000
10% of the final selling price
$5,001 to $32,500
3% of the final selling price (min $500)
Above $32,500
$975
Payment can be made by wire transfer (recommended), certified bank check (U.S. customers only), or credit card (when full payment amount is $5,000 or less).
All bids are binding and cannot be retracted. Failure to make full payment will result in a Default Fee.
If you are looking to finance your purchase, we recommend you get
pre-approved in advance of the auction. Here are three companies we recommend
who specialize in equipment financing:
GE Capital
Thank you for your interest in applying for a GE Capital loan. GE Capital
provides equipment leasing, financing and other services to deliver significant
benefits for your business. Our products and services are customized with
flexible structure and payment terms to match your unique needs and goals. In
order to start the process of applying for a loan, please complete the attached
credit
application and email it to Ron Hayes or fax it to 1+866-401-5114.
Cat Financial - Capital Solutions
Get a Pre-Approved Line of Credit Be prepared for
upcoming auctions by arranging a line of credit from Cat Financial. Time is
money during an auction, and seconds count. Let Cat Financial provide you with
the pre-arranged purchasing power that lets you focus on the equipment you need.
Apply today.
Trucks
If you wish to finance your truck purchase, we recommend that you get pre-approved before the auction.
DriveItNow provides pre-qualification for IronPlanet trucks. Through DriveItNow, you can securely pre-qualify for financing online without providing confidential information such as your social security number or date of birth. There is also NO impact on your credit score. Click on the monthly payment or “Get Financing” link from any live auction truck listing to get started. DriveItNow is a service provided by ACS (Automobile Consumer Services, Inc.)
Warranty by Premium 2000
