Dents; Scrapes; Bent panels; Missing some bolts & hardware; See photos for condition
Steps/Ladders
See photos for condition
Hand Rails
See photos for condition
General Appearance #1
Control Station
Mirrors
Glass
See photos for condition; Left: Cracked: Door
Seats/Armrests
Inoperable slide or adjustment; See photos for condition
Seat Belts
Operational
Horn
Operational
Hydraulic Controls
Steering Controls
Loose
Drivetrain Controls
Oil Pressure
The fault indicator shuts off after the engine oil pressure rises.
Exterior Lights Operational
Some missing
Engine Warning Lights
Operational; Transmission, engine, caution light stayed on, may have fault codes
Travel Alarm
Operational
Gauges
Operational
Hour Meter/Odometer
6,619 Hours; Operational hour meter
- IronPlanet makes no guarantees as to actual hours/miles; we can only report what can be visually observed.
Air Conditioner
Operational
Heater
Inoperable
Limited Function Check
The main components operated except as noted.
Hour Meter/Odometer
Engine
Make and Model
Caterpillar C-9 engine; Serial #: 4ZF20143
Fuel Type
Diesel
Emission Control Label
None found
Blow by @ idle (subjective observation)
Minor
Starter
Operational
Turbo or Blower
Operational
Fuel System
Operational
Exhaust System
See photos for condition; Rusted/damaged stack
Radiator
Low coolant level
Oil Leaks
None seen
Fuel Leaks
None seen
Cooling System Leaks
None seen; Can smell coolant but unable to verify source
Limited Function Check
The engine was difficult to start and ran rough. Engine has miss & low power. See oil report.
Blow by @ idle (subjective observation)
Drivetrain
Operational test is limited to low speed in a confined flat area without load. Differential interlocks, full transmission shifting and functionality of all drive axles cannot be fully verified. Inspector listens for abnormal noises, observes leaks and notes physical damage.
Transmission
Operational; During limited check
Travel Speeds
High; Mid; Low
Service Brakes
Final Drives
Limited Function Check (Drivetrain-Track)
Unable to completely verify transmission performance due to engine condition; Steering & higher ground speeds nearly kills engine. See oil report.
Drivetrain #1
Hydraulics
Pumps (Hydraulics)
Valves
Seepage
Hydraulic Tank
Hoses (Hydraulics)
Blade Lift Cylinders
Fluid accumulation on the left cylinder; Minor to moderate pin and bushing movement
Blade Tilt Cylinders
Oil accumulation on the right cylinder; Minor to moderate pin and bushing movement; Rust on chrome in non working area
Limited Function Check
The hydraulic system was operational without a load.
Hydraulics #1
Chassis
IronPlanet pin connection pivot point wear inspections are limited to sound, sight and feel observations. Dial indicator testing is not performed.
Frame Condition
Roller Frames
Belly pans
Pivot Shafts
No visible leaks
Equalizer Bar Pivot Points
Wear consistent with hours and age
Limited Function Check (Chassis)
The main components were operational when checked without a load.
Push Arm/C-Frame Condition
Push Arm Pivot/C-FrameTrunnions
Minor to moderate movement
Tilt Linkage Pins and Bushings
Minor to moderate movement
Blade Trunnions/bushings
Minor to moderate movement
Limited Function Check (dozer)
The main components were operational with movement as indicated.
Chassis #1
Undercarriage
Undercarriage components photos (links, bushings, sprockets, idlers, rollers, grousers) are selected as representative. Bidders are encouraged to review photos using the zoom feature to judge condition in detail.
Overall width (outside to outside of shoes)
10' 4" Overall width
Track Tensioners
See photos for condition
Shoe Width
36" track shoes; Bent/damaged pads
Grouser Height
Left Side: 44 mm; Right Side: 44 mm
Track link wear
See photos for condition; Master link welded left side
Pins and Bushings Turned?
No
Pins and bushing wear
See photos for condition
Carrier Rollers Wear
See photos for condition
Track Rollers Wear
See photos for condition
Idlers
See photos for condition
Sprockets
See photos for condition
Pins and bushing wear
Specialty
Blade Condition
13' blade; Worn; Dented
Blade Cutting Edge Condition
Reversible-turned; Worn
Specialty #1
Oil Sample Analysis
Engine
Transmission
date of analysis
Jun 12, 2012
Jun 12, 2012
Silicon
6 PPM
87 PPM
Lead
3 PPM
2 PPM
Tin
0 PPM
1 PPM
Copper
11 PPM
248 PPM
Aluminum
3 PPM
2 PPM
Silver
0.1 PPM
0.1 PPM
Nickel
2.3 PPM
1 PPM
Chromium
0.2 PPM
0.1 PPM
Iron
21 PPM
17 PPM
Glycol
NEG
N/A
Water
NEG
NEG
Fuel
<5%
N/A
Disputes:
This item is offered with IronClad Assurance® protection. With IronClad Assurance®, if a buyer discovers that the item is not substantially in the condition as represented in this inspection report, the buyer may submit a written dispute claim to IronPlanet. Following submission of a written dispute claim, IronPlanet will investigate the claim, re-inspecting the equipment item as necessary, and determine a fair and mutually beneficial resolution. Please note that IronPlanet inspections are performed solely for the purpose of reporting the visible condition of the equipment''s major systems and attachments on the day of the inspection and do not include load testing or digging/lifting. These inspections are not designed nor intended to detect latent defects, or conditions that could only be found in connection with the physical dismantling of the equipment or the use of diagnostic tools or techniques. This inspection report includes ratings, comments, and photos of the various components of the item. Knowledgeable buyers are expected to carefully review all of the available information in the inspection report, including all photographs, in order to make the best bidding and buying decision possible.
Buyer is responsible for all costs related to transporting the item.
Item must be picked up within 8 business days of the auction, or the buyer will incur storage charges.
The location information will be provided once full payment has been received.
The buyer will have the option during Checkout to automatically receive competing quotes.
Pickup Terms Failure to follow these terms may result in the seller turning away the attempt to pick up the purchased item.
Hours: 8:30 am–3:30 pm Mon-Fri
You must call at least 24 hours in advance to schedule pickup
Loading Dock Available
Driver MUST bring a copy of the IronPlanet Transportation Release to pick the item up.
Within 3 business days after the auction, the buyer must submit full payment, including applicable taxes and fees.
For this item, payment is due on or before July 17.
This item is subject to Tennessee sales tax. (Read more)
Buyer must pay a transaction fee, based on the final selling price:
Final Selling Price
Transaction Fee
$1 to $5,000
10% of the final selling price
$5,001 to $32,500
3% of the final selling price (min $500)
Above $32,500
$975
Payment can be made by wire transfer (recommended), certified bank check (U.S. customers only), or credit card (when full payment amount is $5,000 or less).
All bids are binding and cannot be retracted. Failure to make full payment will result in a Default Fee.
If you are looking to finance your purchase, we recommend you get
pre-approved in advance of the auction. Here are three companies we recommend
who specialize in equipment financing:
GE Capital
Thank you for your interest in applying for a GE Capital loan. GE Capital
provides equipment leasing, financing and other services to deliver significant
benefits for your business. Our products and services are customized with
flexible structure and payment terms to match your unique needs and goals. In
order to start the process of applying for a loan, please complete the attached
credit
application and email it to Ron Hayes or fax it to 1+866-401-5114.
Cat Financial - Capital Solutions
Get a Pre-Approved Line of Credit Be prepared for
upcoming auctions by arranging a line of credit from Cat Financial. Time is
money during an auction, and seconds count. Let Cat Financial provide you with
the pre-arranged purchasing power that lets you focus on the equipment you need.
Apply today.
Trucks
If you wish to finance your truck purchase, we recommend that you get pre-approved before the auction.
DriveItNow provides pre-qualification for IronPlanet trucks. Through DriveItNow, you can securely pre-qualify for financing online without providing confidential information such as your social security number or date of birth. There is also NO impact on your credit score. Click on the monthly payment or “Get Financing” link from any live auction truck listing to get started. DriveItNow is a service provided by ACS (Automobile Consumer Services, Inc.)
Warranty by Premium 2000
