Enclosed Cab, Sliding Operator Station, Deutz Engine, On Board Generator, 3000mm wide screed, extends to 5000mm,Tar spray down system, including Tartank in front, No CE certificate available from seller - No CE mark on machine,
Meter Reading:
4,311 Hours
Serial Number:
Location:
Ringkobing, Denmark
Shipping:
See shipping details for important pickup requirements and to get a shipping estimate
Inspection Report :
Protected by IronClad Assurance
Payment:
Payment due within 3 business days after auction. See Details
No CE certificate available from seller - No CE mark on machine
Paint
Not original paint; See photos for condition
Sheet Metal (fiberglass) Condition
Minor dents; Scrapes; Surface rust in areas; See photos for condition
Steps/Ladders
See photos for condition
Hand Rails
See photos for condition
General Appearance #1
Control Station
Seats/Armrests
See photos for condition
Seat Belts
Not equipped
Horn
Operational
Hydraulic Controls
Steering Control
Drivetrain Controls
Controls stick
Oil Pressure
The fault indicator shuts off after the engine oil pressure rises.
Exterior Lights Operational
Yes; Some inoperable
Warning Lights
Operational
Gauges
Operational
Hour Meter
4311,3 Hours; Operational hour meter
- IronPlanet makes no guarantees as to actual hours/miles; we can only report what can be visually observed.
Limited Function Check (cs)
The main components are in place and operational.
Hour Meter (Start)
Engine
Make and Model
Deutz; BF6L912 engine; 6 Cylinder Engine
Fuel Type
Diesel
Emission Control Label
None found
Blow by @ idle (subjective observation)
Minor
Starter
Operational
Fuel System
Operational
Exhaust System
No visible damage; See photos for condition
Oil Leaks
See photos; Fluid Accumulation: Valve cover; Fluid Accumulation: Rear of engine
Fuel Leaks
None seen; See photos
Limited Function Check (Engine)
The engine started and ran. See oil report.
Blow by @ idle (subjective observation)
Drivetrain
Operational test is limited to low speed in a confined flat area without load. Differential interlocks, full transmission shifting and functionality of all drive axles cannot be fully verified. Inspector listens for abnormal noises, observes leaks and notes physical damage.
Transmission
Operational
Rear Drive Axle
Drive Motors
Final Drives
Drive Chains/Sprockets
See photos
Limited Function Check
The drivetrain was operational.
Drivetrain #1
Hydraulics
Pumps (Hydraulics)
Fluid accumulation
Valves
Hydraulic Tank
Hoses (Hydraulics)
Screed Angle Cylinders
Minimal pin and bushing movement
Screed Lift Cylinders
Minimal pin and bushing movement
Screed Extension Cylinders
Minimal pin and bushing movement
Limited Function Check
The hydraulic system was operational without a load. See oil report.
Hydraulics #1
Chassis
IronPlanet pin connection pivot point wear inspections are limited to sound, sight and feel observations. Dial indicator testing is not performed.
Screed Model No
VB7076
Screed Control Switches
Screed Lift Arms
Screed Bottom Plate / Mat
Metering Gates
Minor to moderate wear
Auger Control Switches
Auger/ Screw Condition
Feed Conveyors
Not tested, was seized in tar/asphalt.
Conveyor Drive Chains and Sprockets
Push Rollers
Hopper Wings
Screed Heaters
Not operationally checked; Electric Screed Heat
Screed Height Adjustment
Powered adjustment
Screed Slope Adjusters
Screed Angle of Attack Adjusters
Screed Power Extend
Screed Wear Plates
Extension Tubes
End Gates
Spray Down System
Not operationally checked
Limited Function Check
The components that could be checked functioned with wear.
Chassis #1
Undercarriage
Undercarriage components photos (links, bushings, sprockets, idlers, rollers, grousers) are selected as representative. Bidders are encouraged to review photos using the zoom feature to judge condition in detail.
Overall width (outside to outside of shoes)
2400mm Overall width
Track Tensioners
See photos for condition
Shoe Width
300mm track shoes
Grouser Height
Rubberpads bolted on steel.
Track link wear
See photos for condition
Pins and Bushings Turned?
No
Pins and bushing wear
See photos for condition
Carrier Rollers Wear
See photos for condition
Track Rollers Wear
See photos for condition
Idlers
See photos for condition
Sprockets
See photos for condition
Pins and bushing wear
Oil Sample Analysis
Engine
Hydraulic
date of analysis
Jun 19, 2012
Jun 19, 2012
Silicon
12 PPM
1 PPM
Lead
1 PPM
0 PPM
Tin
1 PPM
0 PPM
Copper
6 PPM
2 PPM
Aluminum
3 PPM
0 PPM
Silver
N/A
N/A
Nickel
0 PPM
0 PPM
Chromium
1 PPM
0 PPM
Iron
19 PPM
2 PPM
Glycol
0
N/A
Water
0
NEG
Fuel
N/A
N/A
Disputes:
This item is offered with IronClad Assurance® protection. With IronClad Assurance®, if a buyer discovers that the item is not substantially in the condition as represented in this inspection report, the buyer may submit a written dispute claim to IronPlanet. Following submission of a written dispute claim, IronPlanet will investigate the claim, re-inspecting the equipment item as necessary, and determine a fair and mutually beneficial resolution. Please note that IronPlanet inspections are performed solely for the purpose of reporting the visible condition of the equipment''s major systems and attachments on the day of the inspection and do not include load testing or digging/lifting. These inspections are not designed nor intended to detect latent defects, or conditions that could only be found in connection with the physical dismantling of the equipment or the use of diagnostic tools or techniques. This inspection report includes ratings, comments, and photos of the various components of the item. Knowledgeable buyers are expected to carefully review all of the available information in the inspection report, including all photographs, in order to make the best bidding and buying decision possible.
Buyer is responsible for all costs related to transporting the item.
Item must be picked up within 8 business days of the auction, or the buyer will incur storage charges.
The location information will be provided once full payment has been received.
Pickup Terms Failure to follow these terms may result in the seller turning away the attempt to pick up the purchased item.
Hours: 7am to 3pm
You must call at least 24 hours in advance to schedule pickup
No Loading Dock, Ramps, or Forklift Available: Only RGN or trailers with ramps can be used to pick up this item at this location. Seller will not allow item to be loaded on a step-deck or flatbed trailer without the appropriate ramps.
Driver MUST bring a copy of the IronPlanet Transportation Release to pick the item up.
Within 3 business days after the auction, the buyer must submit full payment, including applicable taxes and fees.
For this item, payment is due on or before March 4.
Buyer must pay a transaction fee, based on the final selling price:
Final Selling Price
Transaction Fee
€1 to €3,000
10% of the final selling price
€3,000 to €32,500
3% of the final selling price (min €300)
Above €32,500
€975
Payment can be made by wire transfer (recommended), certified bank check (U.S. customers only), or credit card (when full payment amount is $5,000 or less).
All bids are binding and cannot be retracted. Failure to make full payment will result in a Default Fee.
If you are looking to finance your purchase, we recommend you get pre-approved in advance of the auction. Here is a company we recommend who specialize in equipment financing:
Cat Financial
Financing for the way you work Your business is always changing, and so are your financial needs. You need quality equipment to get your work done and financing solutions that make sense for you. Count on a company that understands the work you do.
Warranty by Premium 2000
